Sealey BT91/7PF User Manual download pdf

❐ WARNING! Ensure you read, understand and apply the safety and operational

instructions before connecting the tester clamps to the battery. Only when you

are sure that you understand the procedures is it safe to proceed with the testing process.

3.1. Preparation

3.1.1. Check battery casing for cracks or leakage and confirm that it is 6 or 12 volts.

3.1.2. Clean battery terminals.

3.1.3. If possible, check electrolyte levels and top up with distilled water as necessary.

3.2. Connection

❐ WARNING! Ensure vehicle, or battery, is in a well ventilated area before starting test.

3.2.1. Attach positive either clamp to positive (+) battery terminal and the other clamp to negative (-)

terminal. Slightly twist clamps on terminals two or three times to ensure a good electrical contact and

a firm grip. Correct connection is indicated by the meter pointer (fig.1) moving to the right, up the scale.

If the pointer does not move at all there is either a bad connection or the battery is completely dead.

3.2.2. Ensure that the clamp cables are clear of hot or moving engine parts, particularly if a starter or charging

test is to be carried out. Ventilation slots in tester casing should be unobstructed, meter should be easily

visible and load switch accessible.

1.1. PERSONAL PRECAUTIONS

✓ Ensure there is another person within hearing range of your voice and close enough to come to your aid, should a problem

arise when working near a lead-acid battery.

✓ Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.

✓ Have fresh water and soap nearby in case battery acid contacts skin, clothing, or eyes.

✓ Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool, clean running water for at

least 15 minutes and seek immediate medical attention.

✓ Remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current which is high enough

to weld a ring or the like to metal, which would cause severe burns.

✓ Ensure hands, clothing (especially belts) are clear of fan blades and other moving or hot parts of engine, remove ties and contain long hair.

✗ DO NOT smoke or allow a spark or flame in the vicinity of battery or engine.

1.2. GENERAL SAFETY INSTRUCTIONS

✓ Familiarise yourself with the application and limitations of the tester as well as the potential hazards.

Also refer to the vehicle manufacturer’s hand book.

IF IN ANY DOUBT CONSULT AN ELECTRICIAN.

✓ Ensure the tester is in good order and condition before use. If in any doubt do not use the unit and contact an electrician.

✓ Only use recommended attachments and parts. To use non-recommended items may be dangerous and will invalidate your warranty.

✓

Ensure the tester load switch is ‘Off’ before attaching/detaching the power clamps to/from the battery terminals.

✓

Keep tools and other items away from the engine and ensure you can see the battery and working parts of engine clearly.

✓

Confirm that the battery to be tested is 6 or 12 volt and not 24 volt before attaching clamps to battery terminals.

✓ If the tester receives a sharp knock or blow the unit must be checked by a qualified service agent before using.

✓ If the battery terminals are corroded or dirty clean them before attaching the clamps.

✓ Keep children and unauthorised persons away from the working area.

✗ DO NOT dis-assemble the tester for any reason. The tester must only be checked by qualified service personnel.

❐ WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area, or allow them to touch the battery

terminals.

✗ DO NOT pull the cables or clamps from the battery terminals.

✗ DO NOT use the tester in damp, or wet locations and DO NOT use within the vicinity of flammable liquids or gases.

✓

Ensure there is effective ventilation to prevent a build-up of explosive gases, and do not cover or obstruct tester ventilation louvres.

✗ DO NOT use the tester for a task for which it is not designed.

✓ When not in use, store the tester carefully in a safe, dry, childproof location.

✗ DO NOT operate the load switch for more than 10 seconds at a time. (Failure to release the switch after 10 seconds may result in the switch burning out and

invalidating your warranty.)

INSTRUCTIONS FOR:

Professional Battery Drop Tester 6/12V –

Polarity Free

MODEL: BT91/7PF

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,

give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL

INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

DANGER! BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS REASON, IT IS

VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE THE BATTERY TESTER.

Follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you intend to use in the

vicinity of the battery. Remember to review warning marks on all products and on engines.

American pattern drop tester. Polarity free cables - impossible to damage unit by

misconnection. Load applied by internal switchgear - no sparking! Suitable for 6 and 12Volt

batteries. Applies load across cells and measures output on meter. Accurate indication of

battery voltage, faulty cell and short circuited cell.

3. OPERATION

2. INTRODUCTION

fig.1

BT19/7PF Issue No.1 27/06/08

fig.2

LOAD

SWITCH

CABLE

1 2

Summary of Contents

Page 1 - BT91/7PF

❐ WARNING! Ensure you read, understand and apply the safety and operational instructions before connecting the tester clamps to the battery. Only

Page 2 - E-mail: [email protected]

For Jack Sealey Ltd. Sole UK importer of Sealey Power Products.01284 75750001284 703534E-mail: [email protected]: It is our policy to conti

Comments to this Manuals

No comments

Sealey BT91/7PF User Manual

Browse online or download User Manual for Measuring instruments Sealey BT91/7PF. Sealey BT91/7PF User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Measuring instruments Sealey BT91/7PF