Sealey VS0071 User Manual download pdf

INSTRUCTIONS FOR:

ELECTRONIC STETHOSCOPE

Model No: VS0071

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free

performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL

INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. INTRODUCTION

Environmental Protection.

Recycle unwanted materials instead of disposing of them as waste.

All tools, accessories and packaging should be sorted, taken to a recycle centre and disposed of in a manner which is

compatible with the environment.

When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local

solid waste authority for recycling information.



Battery Removal.

See Section 4.1 for battery removal.

 

Dispose of batteries according to local authority guidelines.

Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products

containing batteries (as defined within these regulations), that they are registered with Valpak’s registered compliance scheme.

Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705

1.1. GENERAL SAFETY

 WARNING! Ensure Health & Safety, local authority, and general workshop practice

regulations are adhered to when using this equipment.

 Familiarise yourself with the application and limitations of the equipment, as well as

the specific potential hazards.

  Maintain the equipment in good condition

 Keep the equipment clean for best and safest performance.

 Ensure cables and probe cannot contact moving parts.

  DO NOT place cables and probe near high voltage items - HT leads, spark plugs or

ignition coil.

  DO NOT allow untrained persons to operate the VS0071.

  DO NOT allow children to play with the VS0071.

 DO NOT operate the equipment when you are tired or under the influence of alcohol, drugs or

intoxicating medication.

 When not in use switch off equipment and store in a safe, dry, childproof area.

 For prolonged storage, remove batteriy.

Accurately pinpoints automotive noise and vibrations, which are converted into an electical

signal and amplied.

Long pickup shaft allows use in hard to reach places.

Features a volume control and is supplied with headphones and a 9V battery.

3. OPERATION

4. MAINTENANCE

4.1 To change the battery, remove the cover at the rear of the amplier and

replace battery with a similar 9V unit.

4.2 Periodically wipe the amplier with a damp cloth and mild detergent: do

not use solvents.

4.3 Do not allow unit to become wet; store in cool, dry place.

3.1 Ensure that 9V battery is tted.

3.2 Screw probe into head of amplier.

3.3 Fit headphone plug into socket in the base of the amplier and put headset on.

3.4 Switch unit on by initial movement of thumbwheel. Red LED conrms that unit is switched

on.

3.5 Further movement of the thumbwheel increases the headset volume; about half volume

is the optimum setting for initial use. Increasing the volume may be necessary for faint

sounds, but an increase in background noise will also occur.

3.6 Place the tip of the probe against the suspect part, taking care to comply with safety

instructions in section 1.

3.7 The sound pitch and quality will vary, giving an indication of the location and severity of `

any potential problem.

  WARNING! Prolonged exposure to high volumes of noise, or sudden very loud

noises can result in permanent hearing loss.

Original Language Version

VS007.V3 Issue: 1 - 24/03/10VS0071 Issue: 1 - 04/10/12

Original Language Version

VS007.V3 Issue: 1 - 24/03/10VS0071 Issue: 1 - 04/10/12

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

Sole UK Distributor, Sealey Group,

Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk,

IP32 7AR

www.sealey.co.uk

Web

01284 703534

sales@sealey.co.uk

Summary of Contents

Page 1 - Model No: VS0071

INSTRUCTIONS FOR: ELECTRONIC STETHOSCOPE Model No: VS0071Thank you for purchasing a Sealey product. Manufactured to a high standard this product will,

Comments to this Manuals

No comments

Sealey VS0071 User Manual

Browse online or download User Manual for Measuring instruments Sealey VS0071. Sealey VS0071 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Measuring instruments Sealey VS0071