Sealey CT955 User Manual download pdf

INSTRUCTIONS FOR:

PETROL ENGINE COMPRESSION

TEST KIT 8PC

MODEL NO: CT955.V3

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

1. SAFETY

2. INTRODUCTION

3. OPERATION

 WARNING! Ensure all Health & Safety, local authority and general workshop practice regulations are strictly adhered to when using

tools.

 DO NOT use equipment if damaged.

 Maintain the equipment in good and clean condition for best and safest performance.

 If required, ensure vehicle to be worked on is adequately supported with axle stands, ramps and chocks.

 Wear approved eye protection. A full range of personal safety equipment is available from your Sealey dealer.

 Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.

 Account for all tools and equipment being used and DO NOT leave them in, on or near engine.

 When not in use, place in protective case and store in a safe, dry, childproof area.

 IMPORTANT: Always refer to the vehicle manufacturer’s service instructions, or a proprietary manual, to establish the current procedure

and data. These instructions are provided as a guide only.

 WARNING! The warnings, cautions and instructions referred to in this manual cannot cover all possible conditions and situations that

may occur. It must be understood that common sense and caution are factors which cannot be built into this product, but must be

applied by the operator.

Compression tester fitted with a Ø63mm gauge reading up to 300psi and 20kg/cm². Kit includes 130mm straight and angled push on

connectors, 400mm flexible extension with 10, 12, 14 and 18mm adaptors. Supplied in carry-case.

RELEASE

VALVE

HAND

TIGHTEN

3.1. Test Procedure

 WARNING! Always release the pressure via the Release Valve before disconnecting the tester.

Press the release valve slowly to release the pressure gradually. Refer to Fig.1.

NOTE! A variation in compression readings between cylinders is often a better indication of engine problems than the absolute values

of compression.

3.2. Run the engine until it reaches the normal operating temperature.

3.3. Stop the engine and disconnect all spark plug wires, numbering them according to the cylinder to which they were connected.

3.4. Loosen all spark plugs by about half a turn, but do not remove them.

3.5. Using an air hose or wire brush, remove all the dirt and debris from the spark plug wells.

3.6. Remove the spark plugs and place them on a clean, flat surface in the cylinder order in which they were removed.

3.7. Remove the air filter and set the throttle plates to the wide open position, taking care not to damage the linkage or throttle components.

 IMPORTANT: After test, failure to return the throttle plates to the closed position before starting the engine can cause serious

damage to the engine.

3.8. Disconnect the ignition system, following the manufacturer’s recommendations in the vehicle servicing manual.

3.9. Select the spark plug adaptor required for the vehicle. Screw the adaptor to the hose. Screw the spark plug adaptor and hose assembly

into a spark plug well. Hand tighten only. DO NOT use a wrench. Refer to Fig.2.

3.10. Connect the coupling on the gauge to the hose. Ensure the coupling is fully engaged.

3.11. Crank the engine for at least five compression strokes, or until the pressure reading on the gauge stops rising.

3.12. Record the compression reading, then push the side release valve to relieve the pressure.

3.13. Repeat the test and record the reading. Relieve the pressure and remove the hose and adaptor from the spark plug well.

3.14. Repeat for the remainder of the cylinders.

3.15. You may also connect one of the Push On Connectors straight to the gauge coupling to aid quick installation. Select either the straight

or angled stem for easiest access.

CT955.V3 Issue: 1 - 18/09/14

Original Language Version

Fig.2Fig.1

1 2

Summary of Contents

Page 1 - CT955.V3

INSTRUCTIONS FOR: PETROL ENGINE COMPRESSIONTEST KIT 8PCMODEL NO: CT955.V3IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONA

Page 2 - 5. COMPLETION OF TESTS

CT955.V3 Issue: 1 - 18/09/14NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications

Related models: VSE200

Comments to this Manuals

No comments

Sealey CT955 User Manual

Browse online or download User Manual for Measuring instruments Sealey CT955. Sealey CT955 User Manual

Summary of Contents

Related models: VSE200

Comments to this Manuals

Related products and manuals for Measuring instruments Sealey CT955