Sealey YK509FAH User Manual download pdf

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. INTRODUCTION & SPECIFICATIONS

1. SAFETY INSTRUCTIONS

2.1. GENERAL INFORMATION

Steel frame construction with side mounted air motor powering hydraulic pump

unit, foot pedal operated. Sliding hydraulic ram assembly with lateral travel for

off-centre pressing applications. Fitted with ram pressure gauge. Supplied with

flat pressing plate/V-blocks.

1.1 GENERAL SAFETY

 Familiarise yourself with this products application and limitations, as well as the specific potential hazards peculiar to the press.

 Maintain the press in good condition (use an authorised service agent).

 Replace or repair damaged parts. Use recommended parts only. Non authorised parts may be dangerous and will invalidate the warranty.

 Keep the press clean for best and safest performance.

 Locate the press in a suitable working area for its function, keep area clean, tidy, free from unrelated materials and ensure there is

adequate lighting.

 Ensure the workpiece is correctly secured before operating the press.

 WARNING! Always wear approved eye or face protection when operating the press.

 Remove ill fitting clothing. Remove ties, watches, rings, loose jewellery and contain long hair.

 Keep hands and body clear of the work table when operating the press.

 Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip steel toe-capped shoes/boots.

 Keep children and unauthorised persons away from the working area.

 DO NOT operate the press if any parts are missing as this may cause failure or possible personal injury.

 DO NOT use to compress springs or any other item that could disengage and cause a potential hazard.

 DO NOT stand directly in front of the loaded press and never leave a loaded press unattended.

 DO NOT force the press to achieve a task it was not designed to perform.

 DO NOT make any modifications to the press.

 DO NOT adjust or tamper with the safety valve.

 DO NOT exceed the rated capacity of the press.

 DO NOT apply off centre loads.

 DO NOT allow the workpiece or the arbor plates to fall from the press working bench.

 DO NOT get the press wet or use in damp or wet locations or areas where there is condensation.

 DO NOT operate the press when you are tired, under the influence of alcohol, drugs or intoxicating medication.

 When not in use release pressure from the pump and clean the press. Stand or store the arbors in a safe location.

WARNING! Always position the press against a wall. If the press is situated in the open workshop, it is essential that a guard be

placed at the rear of the unit. This will prevent injury to bystanders in the event of the work piece ejecting suddenly.

 WARNING! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that

may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this

product, but must be applied by the operator.

DANGER! The press is top heavy. If it requires moving after assembly or for

relocation, use suitable slings around the top crossbeam, or lift direct with a

forklift with the forks located under the top crossbeam. DO NOT use a pallet truck.

INSTRUCTIONS FOR:

AIR / HYDRAULIC FLOOR PRESS

WITH FOOT PEDAL

MODELS:

YK509FAH & YK759FAH

YK509FAH & YK759FAH Issue No: 1 - 02/09/08

Model: YK509FAH YK759FAH

Type: Floor Floor

Capacity: 50ton 75ton

Ram Stroke: 200mm 250mm

Lateral Ram Travel: 240mm 285mm

Maximum Height - Ram to Table: 1042mm 884mm

Minimum Height - Ram to Table: 62mm 68mm

Table Aperture: 185/235mm 201/251mm

Working Table Depth: 259mm 279mm

Working Table Width: 730mm 800mm

Overall Height: 1910mm 1923mm

Gauge Included: Yes Yes

Weight: 302kg 438kg

Working Pressure: 108 ~ 123psi 108 ~ 123psi

Air Consumption: 9cfm 9cfm

YK509FAH

1 2 3 4

Summary of Contents

Page 1 - YK509FAH & YK759FAH

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly mai

Page 2 - 3. ASSEMBLY

3. ASSEMBLY3.2 YK509FAH 50TON PRESS ASSEMBLY (use the exploded diagram Fig.1 as a guide to assembly). YK759FAH 75TON PRESS ASSEMBLY (use the expl

Page 3

4.1 INSTALLATION.4.1.1 Securely attach the press to a flat, firm, level surface taking into account clearance for working pieces.  DANGER! The p

Page 4 - YK759FAH

Declaration of Conformity We, the sole importer into the UK, declare that the products listed below are in conformity with the following EEC standards

Related models: YK759FAH | YK509F | YK759F | YK10B | YK10F | YK4B | YC10B | YK30XF | YK10BLG |

Comments to this Manuals

No comments

Sealey YK509FAH User Manual

Browse online or download User Manual for Tools Sealey YK509FAH. Sealey YK509FAH User Manual

Summary of Contents

Related models: YK759FAH | YK509F | YK759F | YK10B | YK10F | YK4B | YC10B | YK30XF | YK10BLG |

Comments to this Manuals

Related products and manuals for Tools Sealey YK509FAH