Sealey LED120P User Manual download pdf

1. SAFETY INSTRUCTIONS

1.1. PLUG & MAINS POWER SUPPLY

 WARNING! It is the owner’s responsibility to read, understand and

comply with the following:

You must check all electrical equipment and appliances to ensure that they are

safe before using. You must inspect power supply leads, plugs and all electrical

connections for wear and damage. You must ensure that the risk of electric

shock is minimised by the installation of appropriate safety devices. An RCCB

(Residual Current Circuit Breaker) should be incorporated in the main

distribution board. We also recommend that an RCD (Residual Current Device)

is used with all electrical products. It is particularly important to use an RCD

together with portable products that are plugged into an electrical supply not

protected by an RCCB. If in doubt consult a qualified electrician. You may

obtain a Residual Current Device by contacting your Sealey dealer. You must

also read and understand the following instructions concerning electrical safety.

1.1.1. The Electricity At Work Act 1989 requires all portable electrical

appliances, if used on business premises, to be tested by a qualified

electrician, using a Portable Appliance Tester (PAT), at least once a

year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical

appliances responsible for the safe condition of the appliance and the

safety of the appliance operator. If in any doubt about electrical

safety, contact a qualified electrician.

1.1.3. Ensure the insulation on all cables and the product itself is safe

before connecting to the power supply. See 1.1.1. & 1.1.2. above and

use a Portable Appliance Tester (PAT).

1.1.4. Ensure that cables are always protected against short circuit and

overload.

1.1.5. Regularly inspect power supply, leads, plugs and all electrical

connections for wear and damage and especially power connections

to ensure that none are loose.

1.1.6. Important: Ensure the voltage marked on the product is the same as

the electrical power supply to be used and check that plugs are fitted

with the correct capacity fuse.

A 13amp plug may require a fuse smaller than 13amps for certain

products, see recommended fuse rating listed below.

1.1.7. DO NOT pull or carry the appliance by the power cable.

1.1.8. DO NOT pull plugs from sockets by the power cable.

1.1.9. DO NOT use worn or damaged leads, plugs or connections.

Immediately replace or have repaired by a qualified electrician.

A U.K. 3 pin 13amp plug with ASTA/BS approval is fitted. In case of

damage, cut off and fit a new plug according to the following

instructions (discard old plug safely). (UK only - see diagram).

Ensure the unit is correctly earthed via a three-pin plug. FOR

230 VOLT 13AMP PLUG SEE fig.1.

a) Connect the GREEN/YELLOW earth wire to the earth terminal

‘E’.

b) Connect the BROWN live wire to live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all wires

have been correctly connected, that the cable external insulation

extends beyond the cable restraint and that the restraint is tight.

1.1.10. Cable extension reels. When a cable extension reel is used it should

be fully unwound before connection. A cable reel with an RCD fitted is

recommended since any product which is plugged into the cable reel

will be protected. The section of the cores of the cable is important

and should be at least 1.5mm², but to be absolutely sure that the

capacity of the cable reel is suitable for this product and for others

that may be used in the other output sockets, we recommend the use

of 2.5mm² section cable.

1.2. LIGHT REWIRING:

 WARNING! Ensure all cables are disconnected from the power

supply before attempting the 0following.

Should you need to re-wire the cable into the lamp, proceed as

follows: Remove back cover of the terminal box, located at the rear of

the lamp, to expose the connection block and wires, see fig.2.

Disconnect and remove the old mains cable.

1.2.1 Slide the gland nut and silicon cable seal over the new cable

before inserting it through the cable entry gland in the base of the

rear cover. Before making the connections, pass the cable through

the cable clamp and tighten it as shown in fig.2.

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

 b) Connect the BROWN live wire to live terminal ‘L’.

 c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

After wiring, check there are no bare wires, that all wires have

been correctly connected and that the cable clamp and cable entry

gland nut are tight.

1.2.2 When wired, check that the weather proofing seal is correctly located in

the back cover recess and then replace the back cover. DO NOT use

worn or damaged leads, plugs or connections. Immediately replace or

have repaired. If in any doubt contact a qualified electrician.

RECOMMENDED 230V

FUSE RATING: 3AMP

INSTRUCTIONS FOR:

LED PORTABLE

FLOODLIGHT 20W 230V

MODEL No: LED120P

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND

CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO

MAY CAUSE DAMAGE, OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.

fig.2

fig.1

Original Language Version

LED120P Issue: 1 - 20/07/12

1 2

Summary of Contents

Page 1 - LED120P

1. SAFETY INSTRUCTIONS1.1. PLUG & MAINS POWER SUPPLY  WARNING! It is the owner’s responsibility to read, understand and comply with the foll

Page 2 - 3. INSTALLATION & USE

Original Language Version 3. INSTALLATION & USE 2. INTRODUCTION & SPECIFICATIONPortable floodlight in die-cast powder coated aluminium hou

Related models: LED130P

Comments to this Manuals

No comments

Sealey LED120P User Manual

Browse online or download User Manual for Lighting Sealey LED120P. Sealey LED120P User Manual

Summary of Contents

Related models: LED130P

Comments to this Manuals

Related products and manuals for Lighting Sealey LED120P