Sealey LED120 User Manual download pdf

INSTRUCTIONS FOR:

LED FLOODLIGHT WITH WALL

BRACKET 20W - 230V

MODEL No: LED120

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND

CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO

MAY CAUSE DAMAGE, OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.

1. SAFETY INSTRUCTIONS

3. INSTALLATION & USE

1.1. ELECTRICAL .

p WARNING! It is the user’s responsibility to read,

understand and comply with the following:

p WARNING! THIS PRODUCT MUST BE INSTALLED BY A

QUALIFIED ELECTRICIAN.

You must check all electrical equipment and appliances to

ensure they are safe before using. You must inspect power

supply leads, plugs and all electrical connections for wear and

damage. You must ensure the risk of electric shock is

minimised by the installation of appropriate safety devices. An

RCCB (Residual Current Circuit Breaker) should be

incorporated in the main distribution board.

You must also read and understand the following instructions

concerning electrical safety:

1.1.1. Ensure the light is connected to an appropriate electrical on/off

switch.

1.1.2. Ensure the insulation on all cables and the product itself is

safe before connecting to the mains power supply.

1.1.3. Ensure that cables are always protected against short circuit

and overload.

1.1.4. Regularly inspect power supply, leads, plugs and all electrical

connections for wear and damage, especially power

connections, to ensure that none are loose.

1.1.5. Important: Ensure the voltage marked on the product is the

same as the electrical power supply to be used.

1.1.6. DO NOT pull power cable once installed.

1.1.7. DO NOT pull power plugs from sockets by the power cable.

1.1.8. DO NOT use worn or damaged leads, plugs or connections.

Immediately replace or have repaired by a qualified Electrician.

1.1.9 Ensure the unit is correctly earthed and wired according

to fig.1 to the right.

Slide the gland nut and silicon cable seal over the cable

before inserting it through the cable entry gland in the

base of the rear cover. Before making the connections,

pass the cable through the cable clamp and tighten it as

shown in fig.1.

a) Connect the GREEN/YELLOW earth wire to the earth

terminal ‘E’.

 b) Connect the BROWN live wire to live terminal ‘L’.

 c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

After wiring, check there are no bare wires, that all wires

have been correctly connected and that the cable clamp

and cable entry gland nut are tight.

1.2. GENERAL SAFETY.

p WARNING! Turn off the mains power supply before

servicing or performing any maintenance.

3 Maintain the light in good condition (Repairs must only be

undertaken by a qualified electrician).

3 Replace or repair damaged parts. Use recommended parts

only, non authorised parts may be dangerous and will invalidate

the warranty.

3 Ensure the light is installed correctly in accordance with these

instruction.

3 Only install the light on a vertical surface. DO NOT fix the light

on any horizontal surface, i.e. to the ceiling or an overhang.

p DANGER! DO NOT direct the light into a person's eyes.

This unit has a very intensive light output, which if

incorrectly used could cause eye damage.

7 DO NOT install the light where it is likely to be knocked or hit.

7 DO NOT install in bathrooms, shower rooms, sauna or such

locations.

7 DO NOT use the light without the front glass shield.

Original Language Version

LED120 Issue: 1 - 17/07/12

2. INTRODUCTION & SPECIFICATION

Mounted in die-cast powder coated aluminium housing with wall

bracket. State of the art LED Chip technology allows ultra bright

illumination whilst still keeping costs lower than traditional halogen

bulbs. Even spread of light across a 120° angle. Supplied without

mains cable and suitable for outdoor mounting.

Power .................20W

Lumen output ........ 1200lm

Supply................230V

3.1. INSTALLATION.

 pWARNING! Ensure the unit is

not connected to the mains

power supply before installation.

3.1.1. Consider the position of unit to

ensure you obtain maximum

benefit from the lighting, and that

an appropriate electrical power

source can be provided.

3.1.2. The light must be mounted

vertically only i.e. on a wall etc.

DO NOT mount horizontally

i.e.ceiling or overhang, DO NOT mount so that the face of the

lamp is pointing upwards, or is facing towards the mounting

surface.

fig.2

fig.1

1 2

Summary of Contents

Page 1 - BRACKET 20W - 230V

INSTRUCTIONS FOR:LED FLOODLIGHT WITH WALLBRACKET 20W - 230VMODEL No: LED120Thank you for purchasing a Sealey product. Manufactured to a high standard

Page 2 - 01284 703534

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prio

Comments to this Manuals

No comments

Sealey LED120 User Manual

Browse online or download User Manual for Lighting Sealey LED120. Sealey LED120 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Sealey LED120