Sealey VS954 User Manual download pdf

INSTRUCTIONS FOR:

LOCK NUT WRENCH

MODEL NO:

VS954

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

 WARNING!: DO NOT use the wrench if damaged. Maintain the wrench in good condition and replace any

damaged or worn parts. Use genuine parts only. Unauthorised parts may be dangerous and will

invalidate the warranty.

 Ensure all workshop safety rules, regulations and conditions are complied with when using the wrench.

 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.

 The work area should be clean, well lit and free from unnecessary clutter.

 Keep children and unauthorised persons away from the working area.

 Ensure that the vehicle on which you are working on is properly supported on axle stands or a hoist.

1. SAFETY INSTRUCTIONS

4. OPERATION

4.1 Before first use lubricate all threads.

4.2 Turn the thread engagement screw (X-see fig.2) anticlockwise to disengage the upper thread.

4.3 Open or close the jaws by turning knurled adjusting knob (6) until they are approximately the

correct distance apart. Place jaws over the lock nut and close them down onto it.

4.4 Engage the upper thread by turning the thread engagement screw clockwise until you feel it

make contact with the thread. Do not screw it down hard as this will lock the upper

thread movement.

4.5 Turn the upper thread driver (4) clockwise to lock the jaws. This movement takes the play out

of the assembly and angles the jaws slightly inwards.

4.6 To loosen the lock nut use a 1/2” or 3/4” breaker bar. To tighten the locknut use a torque wrench

to tighten to the manufacturer's stated specification. Do not use with an impact wrench.

4.7 Where needed, the wrench can be used with the appropriate size pins screwed into the jaws for

those lock nuts with suitable location holes.

2. INTRODUCTION

WARNING! DO

3. SPECIFICATION

● Made from high quality Chrome Vanadium steel for added strength and durabilty.

● Universal fitting, suitable for removing wheel bearing lock nuts found on commercial vehicles.

● For use with hexagonal and octagonal lock nuts and those with and without locating pins.

● Use with 3/4” or 1/2” breaker bar.

● Pin ø: 6, 8 and 10mm.

● Supplied in storage case.

Max torque .................500ft.lb

Pin Ø: ............6mm, 8mm, 10mm

Capacity (Oct) .. 49-143mm across flats

Capacity (Hex) . 49-135mm across flats

Original Language Version

VS954 Issue: 1 - 25/10/12

Fig.1

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1 2

Summary of Contents

Page 1 - LOCK NUT WRENCH

INSTRUCTIONS FOR:LOCK NUT WRENCHMODEL NO: VS954Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used

No. Part No. Description 1 SX250.01 No. 1 JAW 2 SX250.02 No. 2 JAW 3 SX250.03 THREAD 4 SX250.04 HEXAGON DRIVER AND P

Comments to this Manuals

No comments

Sealey VS954 User Manual

Browse online or download User Manual for Tools Sealey VS954. Sealey VS954 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Sealey VS954