Sealey SA393 User Manual download pdf

INSTRUCTIONS FOR:

DIGITAL TYRE INFLATOR WITH TWIN

PUSH-ON CONNECTOR

MODEL NO: SA393

1. SAFETY

3. SPECIFICATION

4. INSTALLATION

2. INTRODUCTION

5. OPERATION

SA393 Issue: 1 - 01/07/14

Original Language Version

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

 Disconnect the tyre inflator from the air supply before changing accessories, servicing or performing any maintenance.

 Keep children and unauthorised persons away from the work area.

 Keep the gauge LCD screen and tyre inflator clean.

 Replace damaged parts with genuine Sealey parts. Unauthorised parts may be dangerous and will invalidate the warranty.

 Check condition of the batteries regularly.

 Check tyre pressures when they are cold.

 DO NOT direct the tyre inflator outlet at yourself or others including animals.

 DO NOTcarry the tyre inflator by the hose, or tug the hose from the air supply.

 DO NOT use the tyre inflator for a task which it is not designed to perform.

 DO NOT operate the tyre inflator when you are tired or under the influence of intoxicating medicines, drugs or alcohol.

 DO NOT operate the tyre inflator if parts are missing or the LCD is damaged, this could be dangerous.

 DO NOT drop or bump the tyre inflator.

 DO NOT get the tyre inflator wet.

 DO NOT operate near appliances with strong magnetic fields, corrosive gasses or corrosive liquids.

Composite body with backlit LCD digital display and rubber protector. Select between bar, psi, kg/cm² or kPa. Supplied with 200mm rubber hose

and push-on connector. Powered by 2 x CR2032 batteries (supplied).

Model No: ...............................................SA393

Range:.........5-150psi(0.344-10.34bar, 0.35-10.55kg/cm², 34.5-1034kPa)

Pressure Units:. ................................psi, bar, kg/cm², kPa

Air Supply Maximum:. ...........150psi, 10.34bar, 10.55kg/cm², 1034kPa

Inlet Size: ...............................................1/4"BSP

Batteries (lithium button cell):.................... 2 x CR2032 (supplied)

4.1. AIR SUPPLY

Recommended hook-up is shown in fig.1. (To avoid possible damage to the gauge see note in fig.1 *IMPORTANT!)

 WARNING! Ensure the air supply is clean and dry. A suitable filter/water trap will be required in the supply line.

4.1.1. An air line pressure up to 150psi can be delivered to the tyre inflator. Please note the maximum available pressure cannot exceed the

supply pressure.

4.1.2. Drain the air tank daily. Water in the air line must be kept to a minimum.

4.1.3. Clean the air inlet filter weekly.

4.1.4. The minimum hose diameter should be 1/4” I.D. and fittings must have the same inside dimensions.

4.1.5. Keep hoses away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.

fig.1

(150psi max)

TWIN PUSH ON

CONNECTOR

SA393

5.1 To Inflate

5.1.1. Be aware of the tyre pressure requirement for the vehicle.

5.1.2. Switch on (fig.2) the tyre inflator and the LCD will display zero. Press and hold the "ON_UNIT" icon to select the units, then release.

5.1.3. Push and hold the tyre inflator connector on to the tyre valve using the most convenient side of the twin valve connector.

Note! Always turn on the gauge before connecting to the tyre valve.

5.1.4. Depress the operating lever fully, momentarily and release to display the tyre pressure.

5.1.5. Depress the operating lever for an appropriate period. Release the lever frequently to check the pressure avoiding over inflation.

5.2. To Deflate

5.2.1. Push and hold the tyre inflator connector on to the tyre valve using the most convenient side of the twin valve connector.

5.2.2. Depress the operating lever partially until air can be heard escaping. Hold for an appropriate period. Fully depress the operating lever

momentarily, then release to display new pressure.

IMPORTANT! Always fully depress the operating lever momentarily and release before reading the tyre pressure. If the gauge

switches off whilst attached to the tyre valve, remove the inflator from the valve before switching back on again.

*IMPORTANT!

Hold with spanner when tightening tting.

1 2

PUSH-ON CONNECTOR 1
6. MAINTENANCE 2

Summary of Contents

Page 1 - PUSH-ON CONNECTOR

INSTRUCTIONS FOR: DIGITAL TYRE INFLATOR WITH TWINPUSH-ON CONNECTORMODEL NO: SA393 1. SAFETY 3. SPECIFICATION 4. INSTALLATION 2. INTRODUCTION 5. O

Page 2 - 6. MAINTENANCE

Environmental ProtectionRecycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, take

Comments to this Manuals

No comments

Sealey SA393 User Manual

Browse online or download User Manual for Tools Sealey SA393. Sealey SA393 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Sealey SA393