Sealey VS0558 User Manual download pdf

INSTRUCTIONS FOR:

FUEL LINE CLAMP AND STOPPER KIT 12

MODEL No: VS0558

1. SAFETY INSTRUCTIONS

 WARNING! Ensure all Health and Safety, local

authority, and general workshop practice regulations

are strictly adhered to when using this product.

 Ensure you have read and understood the safety aspects

of dealing with fuel injection systems and petrol in general

before using this kit.

IMPORTANT: Always refer to the vehicle manufacturer’s

service instructions, or proprietary manual to establish the

current procedures and data for dealing with pressurised

fuel systems.

 Maintain tools in good and clean condition for best and

safest performance.

 Account for all tools and parts being used and do not leave

them in, or on the engine after use.

Fuel Hazards:

 WARNING! Petrol fumes and battery gases are explosive.

 DO NOT smoke or allow an open flame or sparks in the

work area.

 Keep a dry chemical (class B) fire extinguisher near to the

working area.

 Avoid fire hazard by using caution when disconnecting fuel

lines and installing stoppers - some spillage is inevitable.

 When connecting to or disconnecting from a fuel system,

relieve pressure from system and wrap a cloth around the

fuel line fitting to absorb any fuel leakage. Wipe up fuel

spills immediately.

Fuel Leaks:

 DO NOT let fuel drip or spill onto a hot engine.

 Wipe up fuel spills immediately.

 Check all stopper seals are in good condition before use.

 After use, ensure that there are no fuel deposits remaining

on any of the components used .

Personal / Operation:

 Wear approved eye protection. A full range of personal

safety equipment is available from your Sealey dealer.

 Keep yourself, clothing and test equipment away from all

moving or hot engine parts.

 DO NOT wear jewellery and tie back long hair.

 Before working on any fuel system, turn off the ignition

switch and disconnect the battery per manufacturer's

procedure.

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

Original Language Version

VS0558 Issue 1 - 29/03/12

2. INTRODUCTION

3. CONTENTS

A comprehensive kit designed to stop the flow of fuel from fuel

lines after disconnection. Comprises long reach flexi-hose clamp,

fuel pipe separator, six fuel hose plugs and four fuel supply

adaptor clamps with rubber bungs, suitable for banjo and metal

fuel pipes. Compatible with brake, transmission, fuel lines and

other applications.

4. OPERATION

4.1 Relieving fuel system pressure.

 WARNING! Before disconnecting any fuel lines, the

fuel system pressure must be relieved, this will

prevent fuel spraying when a joint is disconnected.

Ensure that you follow the procedures laid down by the

manufacturer of the vehicle that is being worked on.

Refer to the latest published information.

 WARNING! DO NOT assume that all pressure in the

fuel system has been relieved. When disconnecting,

wrap a cloth around the fuel line fitting to absorb any

fuel leakage.

4.2 Extension hose clamp.

Ensure that the rubber hose is positioned within the

clamping area 'A'. See figs.1 & 2. To clamp the pipe turn

the knob 'B' (fig.1) until the pipe is firmly clamped (fig.3).

1 Extension hose clamp - Used for clamping off rubber fuel

hoses. Useful for reaching hoses where access is limited.

2 Clamp (Metal Fuel Pipe) - To close off end of metal fuel

pipe after dismantling.

3 Clamp (Banjo Fitting) - To seal both sides of banjo fuel

fitting after dismantling.

4 Fuel Pipe Separator - Used to undo fuel pipe couplings.

5 Stoppers - Used to close off hoses, vacuum pipes etc. Two

of each size supplied - 3/16", 1/4", 5/16".

g.1

1 2

Summary of Contents

Page 1 - MODEL No: VS0558

INSTRUCTIONS FOR: FUEL LINE CLAMP AND STOPPER KIT 12pc MODEL No: VS0558 1. SAFETY INSTRUCTIONS WARNING! Ensure all Health and Safety, local

Page 2 - IP32 7AR

Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email [email protected] or

Comments to this Manuals

No comments

Sealey VS0558 User Manual

Browse online or download User Manual for Tools Sealey VS0558. Sealey VS0558 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Sealey VS0558