Sealey STBJ10W User Manual download pdf

p WARNING! Before lifting ensure Section 1 Safety Instructions are strictly followed.

3.1. Before using the jack, purge the hydraulic system, in order to eliminate any air that may

have accumulated during transit, refering to fig.1 as follows:

a) Fit jack handle over release valve (1) and turn anti-clockwise to open valve.

b) Insert jack handle into the handle sleeve (2) and pump several times to ensure full

internal lubrication and to bleed air from the system.

c) Fit jack handle back over the release valve (1) and turn clockwise to close.

3.2. Lifting

p WARNING! Ensure you prepare vehicle and use jack according to Section 1 Safety Instructions.

3.2.1. Check that the ground upon which the jack will stand is level and solid.

3.2.2. Position the jack saddle (4) under the vehicle manufacturer’s recommended lifting point. Position jack so as

to avoid having to operate it from under the vehicle and so that the handle can be moved up and down

without hitting any part of the vehicle.

3.2.3. Using the screw extension as necessary, raise the saddle to the lifting point (not STBJ5W). Ensure that the

saddle is correctly centred beneath the lifting point.

INSTRUCTION MANUAL FOR:

TELESCOPIC BOTTLE JACKS

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS JACK CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. RETAIN THESE INSTRUCTIONS FOR FUTURE USE.

Thank you for purchasing a Sealey jack. Manufactured to a high standard this product will, if used according to these instructions and properly

maintained, give you years of trouble free performance.

2. INTRODUCTION & SPECIFICATIONS

1. SAFETY INSTRUCTIONS

MODELS: STBJ5W, STBJ10W, STBJ12W,

Fully tested and complies with the latest CE regulations. Telescopic two stage hydraulic ram gives a much larger maximum lift without

compromising closed height. Base and reservoir machine welded for increased strength and reduced chance of leaking. Threaded pump

assembly allows for easy disassembly and maintenance. STBJ10W and STBJ12W have carrying handles. Supplied with 3pc jacking handle.

In the table below the dimensions are cross-referenced to fig.1.

3. OPERATING INSTRUCTIONS

fig.1

1. Release Valve

2. Handle Sleeve

3. Ram

4. Saddle

3 Regularly inspect and lubricate the jack to ensure it is in good working order and condition. DO NOT use the jack if damaged or a fault is

 suspected - check Section 5 Troubleshooting. If necessary, immediately repair or replace damaged parts.

3 Use recommended parts only, the use of unauthorised parts may be dangerous and will invalidate your warranty.

3 Ensure the work area is clean, tidy and free from unrelated materials and has adequate lighting.

3 Use jack on level and solid ground, preferably concrete. Avoid tarmacadam since jack may sink in.

3 Park the vehicle and apply hand brake (if automatic, place in “Park” mode). Switch off the engine and place chocks under the wheels.

3 Ensure a minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc. to allow for tilting during jacking.

3 Ensure all persons are out of the vehicle before jacking. DO NOT enter vehicle whilst it is supported on the jack or axle stands.

3 Check vehicle weight and recommended lifting points by referring to the vehicle owner’s manual. Ensure the lifting point is not corroded.

3 Check lifting point is centred and stable on jack saddle (off centre loads can slip). Position jack so as to avoid operating it from under vehicle.

3 Keep all unauthorised persons away from the jack when lifting and lowering.

s DANGER! Use the jack for lifting only, NOT for supporting the lifted load. ALWAYS USE ADEQUATELY RATED AXLE STANDS.

3 Keep hands etc. clear of moving parts during raising and lowering of the vehicle.

s DANGER! Roadside wheel changing is hazardous. Be extra vigilant, you may not be able to avoid jacking on tarmacadam. Get everyone

out of vehicle. NEVER go under vehicle. Traffic may cause vehicle to rock. Use hazard warning lights. If in doubt call professional help.

3 When changing a wheel, slightly loosen wheel nuts/bolts prior to jacking vehicle. Screw wheel nuts/bolts back before lowering vehicle. Finally

tighten when vehicle is fully lowered.

3 Use a qualified person to lubricate and maintain the jack. Confirm that only recommended hydraulic jack oil is used during maintenance.

7 DO NOT exceed the rated capacity of the jack and DO NOT operate the jack beyond its maximum pump stroke.

p WARNING! DO NOT allow the vehicle to move, or try to start the engine, when the vehicle is jacked up.

7 DO NOT jack a vehicle if it may result in the spillage of fuel, battery acid, or other dangerous substances.

7 DO NOT place any part of your body under vehicle whilst it is supported by the jack. Wait until adequately rated axle stands have

been correctly positioned.

7 DO NOT use jack to support extensions or cradles. DO NOT modify jack in any way. DO NOT use the jack for any other purpose.

7 DO NOT top up jack with brake fluid. Use Sealey hydraulic oil only (Part No: HJO500MLS or HJO5LS).

7 DO NOT allow untrained persons to operate the jack.

7 DO NOT remove any labels from the jack. If labels are damaged or unclear, replace them.

7 DO NOT operate the jack when you are tired, under the influence of alcohol, drugs or intoxicating medication.

3 Ensure there are no persons or obstructions beneath the vehicle before lowering.

3 Clean and securely stow the jack with the ram in the down position. DO NOT leave the ram extended.

3 When not in use, store the jack in a safe, dry, childproof area.

p WARNING! Remember, it is very dangerous to go under a vehicle supported by a jack even if additional supports are used.

DO NOT go under a vehicle unless it is supported by adequately rated axle stands. NOTE: Seek advice before jacking caravans or trailers.

Original Language Version

STBJ5W, STBJ10W, STBJ12W

Issue: 1 - 26/07/11

Model: STBJ5W STBJ10W STBJ12W

Capacity tonnes ................................ . .5. ...................... 10 . . . . . . . . . . . . . . . . . . . . . . .12

Minimum Height mm (A) . . . . . . . . . . . . . . . . . . . . . . . . .225 ......................210 . . . . . . . . . . . . . . . . . . . . . . 240

Maximum Height mm (D) .........................500 ......................520 . . . . . . . . . . . . . . . . . . . . . . 590

Hydraulic Lift mm (B) ............................275 ......................245 . . . . . . . . . . . . . . . . . . . . . . 270

Screw Extension mm (C) .........................- . . . . . . . . . . . . . . . . . . . . . . . . . 65 . . . . . . . . . . . . . . . . . . . . . . .80

1 2

Summary of Contents

Page 1 - TELESCOPIC BOTTLE JACKS

p WARNING! Before lifting ensure Section 1 Safety Instructions are strictly followed.3.1. Before using the jack, purge the hydraulic system, in or

Page 2 - 5. TROUBLESHOOTING

PROBLEM POSSIBLE CAUSE REMEDYJack will not lift the loadJack does not lift high enough or feels “spongy”Jack lifts but will not hold loadJack will

Related models: STBJ5W | STBJ12W | SBJ10W | SBJ12W | SBJ15W | SBJ20W | SBJ25W | SBJ30W | SBJ5W | SBJ8W | SBJ3W | SBJ2W | STBJ4HLW | SJ50 | SJ10 | SJ12 | SJ15 | SJ2 | SJ20 | SJ3 | SJ5 |

Comments to this Manuals

No comments

Sealey STBJ10W User Manual

Browse online or download User Manual for Tools Sealey STBJ10W. Sealey STBJ10W User Manual

Summary of Contents

Related models: STBJ5W | STBJ12W | SBJ10W | SBJ12W | SBJ15W | SBJ20W | SBJ25W | SBJ30W | SBJ5W | SBJ8W | SBJ3W | SBJ2W | STBJ4HLW | SJ50 | SJ10 | SJ12 | SJ15 | SJ2 | SJ20 | SJ3 | SJ5 |

Comments to this Manuals

Related products and manuals for Tools Sealey STBJ10W