Sealey SSG8E User Manual download pdf

 WARNING! Turn off, or disconnect from air supply before servicing or performing any maintenance and when unit is not in use.

 WARNING! This sand blasting gun will generate gritty dust which could damage surface finishes and contaminate moving parts. It is

recommended that sand blasting be carried out in a dedicated room free from unrelated materials, and where there is adequate lighting.

Where this is not possible consideration should be given to covering exposed surfaces and masking moving parts as necessary.

 WARNING! Wear approved ear, eye, hand and respiratory protection when operating the blaster. A full range of personal safety

equipment is available from your Sealey dealer.

 Maintain correct balance and ensure firm footing by wearing non slip shoes.

 Spillages of abrasive material, which may be slippery, must be cleaned up immediately to avoid injury.

 Maintain the blaster in good condition (use an authorised service agent).

 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

 Keep the unit clean for best and safest performance.

 Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.

 Always keep the blast nozzle directed at the workpiece.

 If a failure or malfunction occurs immediately disconnect from air supply.

 Keep all other persons away from the working area. Contact with high pressure blast or inhaling the dust generated is dangerous. If other

personnel are required in the vicinity of the sand blasting then they must wear protective equipment similar to the operator’s.

 DO NOT use the blaster for any purpose other than that for which it is designed.

 DO NOT attempt to clear a blocked nozzle while the unit is pressurised.

 DO NOT allow untrained persons to operate the blaster.

 DO NOT leave the blaster operating unattended.

 DO NOT stand on the blaster.

 DO NOT direct air from the air hose at yourself or others.

 DO NOT operate system with air supply exceeding 110 psi.

 DO NOT operate the blaster if any parts are missing or damaged as this may cause failure and/or personal injury.

 DO NOT get the blaster wet or use in damp or wet locations or areas where there is condensation.

 DO NOT operate the blaster when you are tired, under the influence of alcohol, drugs or intoxicating medication.

 DO NOT use any abrasive which contains free silica, as indicated in the Health & Safety Guidance Note EH59 (available from HMSO).

NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack

of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person

responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,

give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

2. INTRODUCTION & SPECIFICATION

3. AIR SUPPLY

INSTRUCTIONS FOR:

SANDBLASTING GUN ECONOMY

TYPE WITH 6MM NOzzLE

MODEL No: SSG8E.V3

fig.1

 WARNING! Ensure the air supply does not exceed 110psi

while operating the unit. Too high an air pressure will

shorten the life of the unit due to excessive wear and may

cause damage and/or personal injury.

3.1. Ensure the gun trigger is in the ‘Off’ position before connecting

to the air supply.

3.2. Where possible the compressor should be sited in a separate

room with the connecting airline kept as short as possible.

The compressor should have an air filter and water separator (fig.1).

3.3. Drain the compressor air tank daily. Water in the air line will damage the unit.

3.4. The recommended hook-up procedure is shown in fig.1.

3.5. The minimum hose diameter should be 1/4" I.D. and fittings must have the same inside dimensions.

3.6. Use correct hoses and fittings. DO NOT use quick change couplings as they add weight and can cause failure due to vibration. Add a

leader hose and connect coupling between this and supply hose.

3.7. Keep hoses away from heat, oil and sharp edges. Check hoses for wear and ensure that all connections are secure.

2.1. INTRODUCTION. Model No. SSG8E is suitable for cleaning small areas such as wheels or chassis members. This gun will

accept a variety of abrasives including sand, chilled iron grit and other proprietary types of beading.

2.2. Specifications:

Model no: ............................................................SSG8E.V3

Nozzle ø: ...................................................................... 6mm

Air Pressure: ..........................................................90-110psi

Air Consumption: ................................................... 10-16cfm

2.3. Abrasives:We recommend the use of Sealey Blasting Grit, part nos. B/25KG ( 25kg bag ) or SG10/SAND6 ( 6 X 700g pots ).

Original Language Version

SSG8E V3 Issue: 1 - 22/02/13

1 2

Summary of Contents

Page 1 - TYPE WITH 6MM NOzzLE

 WARNING! Turn off, or disconnect from air supply before servicing or performing any maintenance and when unit is not in use. WARNING! This sand b

Page 2 - SSG8E.V3

5. MAINTENANCE5.1. WARNING! Disconnect from the air supply before performing any maintenance! WARNING! Wear ear, eye, hand and respiratory prote

Comments to this Manuals

No comments

Sealey SSG8E User Manual

Browse online or download User Manual for Tools Sealey SSG8E. Sealey SSG8E User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Sealey SSG8E