Sealey SDAST User Manual download pdf

01284 757500

01284 703534

sales@sealey.co.uk

Sole UK Distributor

Sealey Group,

Bury St. Edmunds, Suffolk.

www.sealey.co.uk

Web

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE

THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

ASSEMBLY INSTRUCTIONS FOR:

DOUBLE STAND FOR AIR PANEL DRYER

MODEL: SDAST.V2

 WARNING! Ensure Health & Safety, local authority and general

workshop practice regulations are adhered to when using this stand.

 Use the stand in a suitable work area.

 Keep work area clean, uncluttered and ensure adequate lighting.

 DO NOT use the stand for a purpose for which it was not designed.

 DO NOT use stand on uneven ground.

 DO NOT use stand if any part is significantly damaged.

 Ensure the SDA01 is securely fixed to the stand using the correct

mounting brackets.

 Keep children and unauthorised persons away from the work area.

Unpack the product and check the contents against the diagram. (Fig. 2).

Should any items be missing or damaged contact your Sealey dealer.

NOTE: GUNS (ITEM 16) NOT SUPPLIED.

Stand will support one or two SDA01 Air Panel Dryers allowing operator

more time for other tasks. Fully adjustable for height and dryer angle.

Supplied with air hoses and fittings. (If used with only one dryer the

second outlet must be closed with a suitable 1/4”BSP plug - not supplied).

4.5 Attach the angle disc (12) to the upright (10) using the pivot bolt

(4) two washers (3) and lock nut (2). Screw the sprung locking

pin (11) to the bracket welded onto the upright (10) allowing the

round ended pin to pass into one of the holes in the angle disc.

4.6 Slide the extended tube (13) into the angled disc (12) and

secure with the locking knob (6).

4.7 Slide the lock shaft (17) onto the extended tube (13) and secure

with a locking knob (6).

4.8 Attach the brackets (15), one on either side of the lock shaft

(17) and secure using locking knobs (6).

4.9 Insert the threaded portion at the base of each SDA01 dryer

handle (16) through the hole in each support bracket (15).

Retain each dryer on each bracket by screwing an internally

threaded joint (18) to clamp each dryer head in position.

4.10 Attach a coiled air hose (14) to each dryer head by screwing it

into the other end of the internally threaded connector.

4.11 Place the air inlet block (9) onto the adjustable bracket (7).

Pass the external thread of the connector (8) through the under

side of the bracket and screw it into the underside of the block.

Tighten the connector until the air inlet block is firmly clamped

onto the bracket.

4.12 Screw the other end of the two air hoses (14) into either side of

the air inlet block (9).

4.13 Tighten all bolts to conclude assembly.

Fig.1

Fig. 2

SDAST.V2 ISSUE NO.1 - 28/03/08

Note: All number references are to Fig.2 below.

4.1 Take the two leg components (5) and loosely bolt the two

upper brackets together using four bolts (20) and four nuts (21).

4.2 Slide the square bottom tube (19) in between the brackets and

further tighten the fixings to clamp the bottom end of the tube

in position. Ensure that the hole for the clamping knob (6) is at

the top of tube.

4.3 Attach the two base feet tubes (1) to the two legs (5) using two

bolts (4) two washers (3) and two nuts (2) on each side.

Ensure that the feet are offset in the same direction.

4.4 Slide the adjustable bracket (7) onto the upright (10)

ensuring that the locking knob will face the front.

Slide the upright assembly (10) into the base tube (19) and lock

it at desired height using lock knob (6).

g.1

g.2

1. SAFETY INSTRUCTIONS

2. DESCRIPTION

3. CONTENTS

4. ASSEMBLY

SDAST.V2 1

Summary of Contents

Page 1 - SDAST.V2

01284 75750001284 [email protected] UK DistributorSealey Group,Bury St. Edmunds, Suffolk.www.sealey.co.ukWebemailNOTE: It is our policy

Comments to this Manuals

No comments

Sealey SDAST User Manual

Browse online or download User Manual for Tools Sealey SDAST. Sealey SDAST User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Sealey SDAST