Sealey SG14 User Manual download pdf

1. SAFETY INSTRUCTIONS

 WARNING!Disconnect the gun from the air supply before changing accessories, servicing or performing any

maintenance.

 Maintain the gun in good condition. Replace or repair damaged parts. Use recommended parts only.

Unauthorised parts may be dangerous and will invalidate the warranty.

 Keep the gun clean and rinse out nozzle and pipes with thinners

after use.

 WARNING! If gun components become blocked there is a danger

of excessive pressure building up in unit causing the canister to burst.

 Locate the gun in a suitable, well ventilated area. Keep area clean,

tidy and free from unrelated materials and ensure there is adequate

lighting.

 Remove ill fitting clothing. Remove ties, watches, rings and other

loose jewellery and contain long hair.

 Keep children and unauthorised persons away from the working area.

 Avoid unintentional operation.

 Ensure coating/wax manufacturer’s instructions are carefully

followed.

 DO NOT hold gun or attachments close to your face (especially

eyes, ears, etc.) and do not point gun or air hose at other persons

or animals.

 DO NOT carry by the air hose, or yank the hose or the gun from

the air supply.

 DO NOT use the gun for any purpose other than for which it is

designed and do not use with any other fluid.

 DO NOT operate the gun if damaged.

 When not in use disconnect from the air supply and store in a safe,

dry, childproof area.

2. INTRODUCTION & SPECIFICATION

Accepts most popular types of 1ltr coating tins.

3.1 AIR SUPPLY (For recommended hook-up, see fig.2.)

3.1.1 Ensure air valve is in "off" position before

connecting to the air supply.

3.1.2 An air pressure of no more than 90psi and an air

volume of 8cfm will be required.

3.1.3  WARNING! Ensure air supply does not

exceed 90psi. Too high a pressure will shorten

the product life and may be dangerous, causing

damage and/or personal injury.

3.1.4 Drain air supply tank daily. Water in the air line will

damage the gun and will invalidate your warranty.

3.1.5 Clean air inlet filter screen weekly.

3.1.6 Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The

minimum hose and fittings diameter should be 10mm I.D.

3.1.7 Keep hoses away from heat, oil and sharp edges. Check hoses for wear and make certain that all

connections are secure.

PREPARING THE GUN FOR USE

Fig 2

Air Pressure: . . . . . . . . . . . . . . . . . . . . . . . . . 90psi

Air Consumption:.......................8cfm

Air Inlet: ........................... 1/4”BSP

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,

WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH

IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE

THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

INSTRUCTIONS FOR:

UNDER-BODY COATING GUN

MODEL NO: SG14.V3

Fig 1

Original Language Version

SG14.V3 Issue: 2 - 09/12/09

1 2

Summary of Contents

Page 1 - UNDER-BODY COATING GUN

1. SAFETY INSTRUCTIONS WARNING!Disconnect the gun from the air supply before changing accessories, servicing or performing any maintenance.

Page 2 - 5. MAINTAINANCE

 WARNING! Ensure you read, understand and apply the safety instructions in Section 1 and follow the manufacturer’s instructions on the und

Related models: AK42 | SG139 |

Comments to this Manuals

No comments

Sealey SG14 User Manual

Browse online or download User Manual for Tools Sealey SG14. Sealey SG14 User Manual

Summary of Contents

Related models: AK42 | SG139 |

Comments to this Manuals

Related products and manuals for Tools Sealey SG14