Sealey SA701 User Manual
Browse online or download User Manual for Tools Sealey SA701. Sealey SA701 User Manual
- Page / 3
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
1.1. Operational Safety
p WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered
to when using this equipment.
p WARNING!Disconnect from air supply before changing accessories or servicing.
3 Maintain the sander in good condition (use an authorised service agent).
3 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and
will invalidate the warranty.
3 Use in a suitable clean and tidy work area and ensure there is adequate lighting.
3 Before each use check abrasive pads for condition. If worn or damaged replace immediately.
3 Ensure the abrasive pad rating is the same as, or, greater than the RPM rating of the sander.
3 Ensure there are no flammable or combustible materials near the work area.
p WARNING! Always wear approved eye or face and hand protection when operating the sander.
3 Use face, dust, or respiratory protection in accordance with COSHH regulations.
3 Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
3 Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back
long hair.
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3 Keep children and unauthorised persons away from the work area.
3 Check moving parts alignment on a regular basis.
3 Ensure workpiece is secure before operating the sander. Never hold a workpiece by hand.
3 Check the workpiece to ensure there are no protruding screws, bolts, nuts, nails, stones, etc.
3 Avoid unintentional starting.
p WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure is no more
than 90psi.
3 Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure
that all connections are secure.
3 Prolonged exposure to vibration from this sander poses a health risk. It is the owner’s responsibility to
correctly assess the potential hazard and issue guidelines for safe periods of use and offer suitable
protective equipment.
7 DO NOT use the sander for a task it is not designed to perform.
7 DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.
p WARNING! DO NOT sand any materials containing asbestos.
7 DO NOT carry the sander by the hose, or yank the hose from the air supply.
7 DO NOT force, or apply heavy pressure to the sander, let the sander do the work.
7 DO NOT place air line attachments close to your face and DO NOT point at other persons or animals.
7 DO NOT operate sander when you are tired or under
the influence of alcohol, drugs or intoxicating
medication.
7 DO NOT use sander where there are flammable
liquids, solids or gases such as paint solvents and
including waste wiping or cleaning rags etc.
7 DO NOT carry the sander with your finger on the
power lever.
7 DO NOT direct air from the air hose at yourself or
others.
3 When not in use disconnect from air supply and store
in a safe, dry, childproof location.
Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
INSTRUCTIONS FOR:
AIR ANGLE ORBITAL
SANDER 75mm
MODEL No: SA701.V2
1. SAFETY INSTRUCTIONS
Original Language Version
SA701.V2 Issue: 1 - 12/10/11
fig.1
Summary of Contents
Page 1 - SA701.V2
1.1. Operational Safetyp WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using
Page 2 - 3. PREPARING TOOL FOR USE
3.1. Air Supply3.1.1. Ensure the sander air control valve (or throttle) is in the "Off" position before connecting to the air supply.3.1.2
Page 3 - 5. MAINTENANCE
p WARNING!Disconnect sander from air supply before changing accessories, servicing or performing maintenance.Replace or repair damaged parts. Us
Related products and manuals for Tools Sealey SA701
Tools Sealey SA721 User Manual
(4 pages)
(4 pages)
Tools Sealey SA800 User Manual
(4 pages)
(4 pages)
Tools Sealey SA77 User Manual
(4 pages)
(4 pages)
Tools Sealey SA802 User Manual
(4 pages)
(4 pages)
Tools Sealey MAT150AS User Manual
(4 pages)
(4 pages)
Tools Sealey SA34 User Manual
(4 pages)
(4 pages)
Tools Sealey S01045 User Manual
(4 pages)
(4 pages)
Tools Sealey GSA345 User Manual
(3 pages)
(3 pages)
Tools Sealey SA342 User Manual
(4 pages)
(4 pages)
Tools Sealey SA347 User Manual
(4 pages)
(4 pages)
Tools Sealey SA57 User Manual
(3 pages)
(3 pages)
Tools Sealey SA623 User Manual
(3 pages)
(3 pages)
Tools Sealey RE901 User Manual
(2 pages)
(2 pages)
Tools Sealey WS570 User Manual
(2 pages)
(2 pages)
Tools Sealey WS680 User Manual
(2 pages)
(2 pages)
Tools Sealey WS650 User Manual
(2 pages)
(2 pages)
Tools Sealey SM23/2 User Manual
(3 pages)
(3 pages)
Tools Sealey AK396 User Manual
(3 pages)
(3 pages)
Tools Sealey AK39602 User Manual
(2 pages)
(2 pages)
Tools Sealey AK3981 User Manual
(1 pages)
(1 pages)
Jabra Bezprzewodowe zestawy słuchawkowe podręczniki użytkownika
Zaczynanie od F
Comments to this Manuals