Sealey 2000ESLE User Manual download pdf (Page 1)

3 Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use

genuine parts only. The use of unapproved parts may be dangerous and will invalidate the warranty.

3 Locate the jack in a suitable, well lit working area.

3 Keep working area clean and tidy and free from unrelated materials.

3 Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.

3 Place wedges under wheels of a vehicle, but ensure wheels of jack can move freely.

3 Ensure the vehicle handbrake is engaged, engine is switched off and transmission is in gear (or “PARK” if an automatic).

3 Ensure minimum distance of 0.5m between vehicle and static objects such as doors, walls, etc., to allow for vehicle tilting.

3 Ensure there are no passengers in the vehicle.

3 Ensure all non-essential persons keep a safe distance whilst the jack is in use.

3 Only place jack under those lifting points recommended by vehicle manufacturer (see vehicle hand book).

3 Check the lifting point is stable and centred on the jack saddle.

3 Ensure the jack wheels are free to move and that there are no obstructions.

3 Use suitable capacity axle stands under the vehicle before proceeding with any task.

3 Ensure there are no persons or obstructions beneath the vehicle before lowering.

3 Use a qualified person to maintain or repair the jack's hydraulic system.

p DANGER: Use the jack for lifting only.

7 DO NOT use for supporting the lifted load.

7 DO NOT operate the jack if damaged.

7 DO NOT allow untrained persons to operate the jack.

7 DO NOT exceed the rated capacity of the jack.

7 DO NOT allow the vehicle or the jack to move while supported by the jack.

7 DO NOT jack the vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous substances.

7 DO NOT work under the vehicle until the axle stands have been correctly positioned.

7 DO NOT use the jack for purposes other than which it is intended.

7 DO NOT top up the hydraulic system with brake fluid. Use hydraulic jack oil only.

7 DO NOT adjust the safety overload valve.

7 When not in use store the jack, fully lowered, handle removed in a safe, dry, childproof area.

Original Language Version

2000ESLE/3000ESLE Issue: 1 - 10/04/14

INSTRUCTIONS FOR:

TROLLEY JACK 2TONNE/3TONNE

EUROPEAN STYLE LOW ENTRY

MODEL No's

2000ESLE & 3000ESL

European style trolley jacks feature a low prole lifting arm and extended access platform for use on low slung vehicles. Lift-and-twist 'Dead

Man' lowering mechanism operates via 'D' shaped handle and prevents accidental lowering; lowers rapidly when no load is attached and pro-

vides smooth, slow, controlled lowering with a load. Nylon wheels tted which are quiet in operation and help prevent damage to garage oors.

Foot pedal for quick approach of the lifting saddle to the vehicle. Also includes removable rubber saddle pad and built-in tool tray for fasteners

and tools.

Model No: 2000ESLE 3000ESLE

A 75 100

B 445 470

C 135 185

D 520 570

E 960 1070

F 1852 1980

G 375 375

H 263 275

1. SAFETY

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

2. INTRODUCTION

3. SPECIFICATION

Model No: 2000ESLE Model No: 3000ESLE

Capacity:................................. 2tonne Capacity:................................. 3tonne

Min. saddle height:.................. 75mm Min. saddle height:.................. 100mm

Max. saddle height:................. 520mm Max. saddle height:................. 570mm

Chassis height:....................... 135mm Chassis height:....................... 185mm

Length:.................................... 960mm Length:.................................... 1070mm

Weight:.................................... 42.0kg Weight:.................................... 50.3kg

Sweep backwards and

forwards to elevate jack

Lift and rotate clockwise

to lower elevated jack.

fig.1

1 2 3

Summary of Contents

Page 1 - 2000ESLE & 3000ESL

3 Ensure the jack is in sound condition and good working order. Take action for immediate repair or replacement of damaged parts. Use genuine pa

Page 2 - 6. MAINTENANCE

4.1. Place the handle onto the jacking lever tube and fix with supplied M6 X 16 cap screw as shown in fig.2.4.2. Offer the jacking lever tube into t

Page 3 - 7. TROUBLE SHOOTING

7. TROUBLE SHOOTINGIMPORTANT: MAINTENANCE OR REPAIR OF HYDRAULIC SYSTEMS MUST ONLY BE PERFORMED BY A QUALIFIED PERSON.PROBLEM POSSIBLE CAUSE REME

Related models: 3000ESLE

Comments to this Manuals

No comments

Sealey 2000ESLE User Manual Page 1

Browse online or download User Manual for Tools Sealey 2000ESLE. Sealey 2000ESLE User Manual

Summary of Contents

Related models: 3000ESLE

Comments to this Manuals

Sealey 2000ESLE User Manual Page 1

Browse online or download User Manual for Tools Sealey 2000ESLE. Sealey 2000ESLE User Manual

Summary of Contents

Related models: 3000ESLE

Comments to this Manuals

Related products and manuals for Tools Sealey 2000ESLE