Sealey WPS062S User Manual download pdf

INSTRUCTIONS FOR:

SURFACE MOUNTING BOOSTER PUMP

STAINLESS STEEL 62LTR/MIN 230V

MODEL No: WPS062S

Manufactured from high impact stainless steel for added durability and rust proofing. Ideal for boosting or maintaining water pressure within the home or garden

water supplies. Fitted with automatic pressure cut-off and non-return valve. Suitable for lifting water up to 8 metres.

1.2. GENERAL SAFETY

 WARNING! Pump must be used in accordance with Health & Safety, government, local authority and water authority rules and regulations.

 Familiarise yourself with the application, limitations and potential hazards peculiar to the pump.

 WARNING!Disconnect the pump from the mains power before servicing or performing any maintenance.

 Maintain the pump in good condition (use an authorised service agent). Keep the pump clean.

 Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

 Only use for pumping cold or warm water (NOT exceeding 35°C).

 If used in situations of possible flooding, user is responsible for installing appropriate back up procedures, alarms etc. in case of pump failure.

 If used with swimming pools, fish ponds, etc., ensure areas are clear of people and animals (including removal of fish from ponds). Note that this pump is not

designed for continuous use in a fish pond or similar water feature or display.

 DO NOT operate the pump if any parts are damaged or missing as this may cause failure and/or possible personal injury.

 DO NOT use the pump for any purpose other than for which it is designed.

 DO NOT use to pump chemicals, fuels, fatty liquids or salt water.

 DO NOT pump sludge, sand, gravel, mud, or fibrous materials. Ensure the inlet hose will NOT pick up any solid

materials. Sand and such substances will reduce working life of pump, and invalidate your warranty.

 DO NOT use to pump septic tanks or settling pits.

 DO NOT submerge the pump or the electrical cable in water. Protect the pump from external wet conditions.

 DO NOT operate pump during freezing temperatures. DO NOT allow any part of the pump or pipes to freeze.

 DO NOT carry pump by the cable, or piping. Only use the handle.

 When not in use switch off pump and remove plug from power supply. Rinse pump, drain out any water and store

in a frost free, safe location.

 WARNING! DO NOT allow uncontrolled discharge of contaminated water, thus polluting the environment.

1.1. ELECTRICAL SAFETY

  WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other connectors

for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A Residual Current

Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current Device (RCD) is used.

It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by an RCCB. If in any doubt consult

a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.

You must also read and understand the following instructions concerning electrical safety.

1.1.1. The Electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified electrician, using a

Portable Appliance Tester (PAT), at least once a year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances and the safety of the

appliance operators. If in any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2. and use a Portable

Appliance Tester.

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none is loose.

1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply to be used and that the plug is fitted with the correct fuse - see

fuse rating at right.

1.1.7. DO NOT pull or carry the appliance by the power cable.

1.1.8. DO NOT pull the plug from the socket by the cable.

1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or

replaced by a qualified electrician. When a BS 1363/A UK 3 pin plug is damaged, cut the cable just

above the plug and dispose of the plug safely.

Fit a new plug according to the following instructions (UK only).

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all wires have been correctly

connected, that the cable outer insulation extends beyond the cable restraint and that the restraint is

tight. Double insulated products, which are always marked with this symbol , are fitted with live

(brown) and neutral (blue) wires only. To rewire, connect the wires as indicated above -

DO NOT connect either wire to the earth terminal.

1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you

must contact a qualified electrician to ensure that a suitably rated supply is available.

We recommend that you discuss the installation of an industrial round pin plug and socket with your electrician.

1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance plugged into it will be

protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the reel is suitable for this

product and for others which may be used in the other output sockets, we recommend the use of 2.5mm² section cable.

RECOMMENDED

FUSE RATING: 13AMP

Original Language Version

WPS062S Issue: 2(SP)- 23/07/14

NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and

knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children should be

supervised to ensure that they do not play with the appliance.

Model No. Cut-Out Outlet Maximum Maximum Motor Input Maximum Maximum

Female Output Head Particle Size Suction Height

WPB062S Manual 1" BSP 62ltr/min 46mtr 1200W 230V 1mm 8mtr

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

1. SAFETY

2. INTRODUCTION

3. SPECIFICATION

1 2

Summary of Contents

Page 1 - WPS062S

INSTRUCTIONS FOR:SURFACE MOUNTING BOOSTER PUMPSTAINLESS STEEL 62LTR/MIN 230VMODEL No: WPS062SManufactured from high impact stainless steel for added d

Page 2 - 6. TROUBLESHOOTING

The pump may be gravity or suction fed. Gravity feed is the preferred arrangement as this will place less strain on the long term operation of th

Comments to this Manuals

No comments

Sealey WPS062S User Manual

Browse online or download User Manual for Pumps Sealey WPS062S. Sealey WPS062S User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Pumps Sealey WPS062S