Sealey TP9912 User Manual download pdf

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.1. ELECTRICAL SAFETY

 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other

connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.

A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current

Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected by

an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.

You must also read and understand the following instructions concerning electrical safety.

1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances

and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. See 1.1.1. and 1.1.2.

and use a Portable Appliance Tester.

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all

connections to ensure that none is loose.

1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply

to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7. DO NOT pull or carry the appliance by the power cable.

N.B: Sections 1.1.8 to 1.1.10 inc refer to TP99230 only.

1.1.8. DO NOT pull the plug from the socket by the cable.

1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty

item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK

3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.

Fit a new plug according to the following instructions (UK only).

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer

insulation extends beyond the cable restraint and that the restraint is tight.

Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.

To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.

1.1.10. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance

plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that the

capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use

of 2.5mm² section cable.

FUSE RATING 13A (TP99230)

1.2. GENERAL SAFETY

 WARNING! Ensure health & safety, government and local authority regulations relating to the transfer of AdBlue® are adhered to when

using this equipment. Familiarise yourself with the pump's applications and limitations, and specific potential hazards peculiar to the pump.

 WARNING! These pumps are designed for use with urea and aqueous media only. DO NOT use for petrol or similar explosive liquids.

 DANGER: The electric pump is not protected against explosion and should therefore not be operated in areas where there

is a risk of explosion.

 WARNING! Disconnect the pump from the mains or battery power before demounting, servicing or performing any maintenance.

 Maintain pump in good condition (use authorised service agent). Drain pump and pipes before dismantling.

 Maintain correct balance and footing when installing and using the pump. Ensure the floor is not slippery and wear non slip shoes.

 Ensure the transfer area is free of clutter and has adequate lighting.

 Ensure that the voltage of the pump matches the voltage of the supply.

 Keep children and unauthorised persons away from the working area.

 Replace/repair damaged parts. Use genuine parts. Unauthorised parts are dangerous and will invalidate warranty.

 DO NOT use the pump without the delivery nozzle attached.

 DO NOT start or stop the pump by switching on or off at the mains power supply. or disconnecting from battery.

 DO NOT operate the unit with wet hands. We recommend use of chemical resistant gloves and goggles.

 DO NOT run the pump dry. If this occurs the pump could be damaged and your warranty will be invalidated.

 IMPORTANT: It is the installer’s responsibility to ensure that all supply pipes, fixtures and fittings are adequate for the safe flow of liquid urea.

Original Language Version

TP9912,TP99230 Issue: 1 - 05/06/13

INSTRUCTIONS FOR:

ADBLUE® TRANSFER PUMPS

PORTABLE 12V, 230V

MODEL NO'S: TP9912,TP99230

2. INTRODUCTION & SPECIFICATIONS

Electric 12V or 230V membrane pump specifically designed for the distribution of AdBlue®. Self-priming unit provides a flow rate of up to

40ltr/min. Supplied with 4mtr hose, manual delivery nozzle and battery clips (12V) or BS approved plug (230V). All materials and seals used in

these pumps are suitable for use with AdBlue®.

1 2

Summary of Contents

Page 1 - TP9912,TP99230

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly mai

Page 2 - 5. MAINTENANCE

3. INSTALLATION & ASSEMBLY 4. OPERATIONOriginal Language VersionTP9912,TP99230 Issue: 1- 05/06/13g.1g.23.1. Attach the feet of the pump uni

Related models: TP99230

Comments to this Manuals

No comments

Sealey TP9912 User Manual

Browse online or download User Manual for Hardware Sealey TP9912. Sealey TP9912 User Manual

Summary of Contents

Related models: TP99230

Comments to this Manuals

Related products and manuals for Hardware Sealey TP9912