Sealey SWS05 User Manual download pdf

Note: Inadequate maintenance is the most common cause of alarm failure; therefore, test your system at least once per

week to be sure the sensors and sirens are working properly. Although having an alarm system may make you eligible

for reduced insurance premiums, the system is no substitute for insurance.

1. Introduction

The Wireless Home Protection System Wireless Keypad Control Unit allows you to operate the system remotely,

from inside or outside the property. Keypad control allows you to change the security PIN and manage the

alarm system.

2. Operation

2.1 Powering up the Wireless Keypad control unit

● Requires CR2032 x 2 batteries (included)

● Remove the battery cover

● Insert new batteries noting the polarity

● Replace the battery cover

**Low Battery indication – LED will ash every 3 seconds**

2.2. LED indication

● LED ashes once to indicate valid operation or valid PIN

● LED ashes four times to indicate invalid operation was performed or invalid PIN

2.3. Changing new PIN

● Enter the default PIN

● Press

● Press and then enter your new PIN

● Press and re-enter your new PIN

● Press

● LED ashes once to indicate the PIN has been changed successfully. LED ashes four times to indicate the PIN has not

been changed, please re-enter your PIN.

2.4. Enroling the Keypad control onto the Smart Panel

Smart Panel

● Press PIN on Smart Panel & then

● Press and then to enter the enrol mode

● The LCD display ashes the ID no. of the controller to be enroled. E.g. when enroling the 1st controller, ID no. “01”

will ash. Once the 2nd controller is enroled, the “02” will ash ready for a 2nd controller to be enroled.

Keypad Control

● Press PIN on Keypad control and then

● Press any function button - , , or

● One Beep indicates the controller was enroled to the Smart Panel successfully.

2.6. Deleting a Keypad control

If the keypad control is damaged or lost, it can be deleted from the system as follows:

Smart Panel

● Press PIN on Smart Panel & then

● Press and then 5 to enter the Deleting mode.

● Then input the number of the Keypad Control you wish to delete from the system

WIRELESS KEYPAD

CONTROL UNIT

INSTALLATION AND OPERATING INSTRUCTIONS

Model No: SWS05

K 100 Die-line

Please keep these instructions in a safe place for future reference.

Kit contents

● 1 x Wireless Keypad Control Unit

● 2 x CR2032 batteries (included)

● 1 x Instruction leaet

● 1 x Screw and Screw jacket set

2.7. Operation the Wireless Keypad control

ARM

● Press PIN, then press

● Press

ALERT

● Press PIN, then press

● Press

HOME

● Press PIN, then press

● Press

DISARM

● Press PIN, then press

● Press

PANIC

●

Press + at the same time

●

The system is immediately activated

2.8. Reset PIN

After inserting the batteries, press for 3 seconds (LED lights will ash). The LED lights turn o indicating the PIN

has returned to the factory default

3. Maintenance

The product may be c

leaned with a soft damp cloth and then wiped dry. Do not use abrasive, solvent based or aerosol

cleaners as this may damage and/or discolour the product. Do not allow water to enter or attempt to clean inside the

unit.

4. Batteries

Do not allow the batteries to corrode or leak as this may cause permanent damage to the product. Take care to insert

the batteries with the correct polarity as shown inside the battery compartments. Do not mix new and old batteries or

dierent types of batteries. Do no

t use rechargeable batteries. At the end of their useful life the batteries should be

disposed of via a suitable recycling centre. Do not dispose of with your normal household waste. DO NOT BURN.

5. Alarm System Limitations

Even the most advanced alarm systems cannot guarantee 100% protection against burglary or environmental

problems. All alarm systems are subject to possible compromise or failure-to-warn for a variety of reasons. Please note

that you may encounter problems with your system if:

• The sensors are not placed within hearing range of persons sleeping or remote parts of the premises.

• The sensors are placed behind doors or other obstacles.

• Intruders gain access t

hrough unprotected points of entry (where sensors are not located).

• Intruders have the technical means of bypassing, jamming, or disconnecting all or part of the system.

• The power to the sensors is inadequate or disconnected.

• The sensors are not located in proper environmental/temperature conditions i.e. too close to a heat source.

Function Buttons

Programming

Buttons

Model No: SWS05 1

Summary of Contents

Page 1 - Model No: SWS05

Note: Inadequate maintenance is the most common cause of alarm failure; therefore, test your system at least once per week to be sure the sensors and

Comments to this Manuals

No comments

Sealey SWS05 User Manual

Browse online or download User Manual for Equipment Sealey SWS05. Sealey SWS05 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Sealey SWS05