Sealey AP6572 User Manual download pdf

INSTRUCTIONS FOR:

RACKING UNIT WITH 4 MESH SHELVES

800KG CAPACITY PER SHELF

MODEL NO: AP6572

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.1 GENERAL SAFETY

 WARNING! Ensure Health & Safety, and local authority regulations

are adhered to when assembling and using these shelves.

 Locate shelves in a suitable area where they will not be an

obstruction.

 Keep the general area clean, uncluttered and ensure there is

adequate lighting.

 WARNING! Erect shelves on a level and solid surface such as

concrete.

 Keep children and unauthorised persons away from the storage

area.

 DO NOT use the shelves for any purpose other than that for

which they are designed.

 DO NOT site the shelves out of doors.

 DO NOT get the shelves wet or use in damp or wet locations or

areas where there is condensation.

 DO NOT clean the shelf supports with any solvents which may

damage the coated surface.

 Ensure that the shelves are properly assembled before loading

them with heavy items.

 Maximum load for each shelf is 800kg. Load must be evenly

distributed.

 Where possible the unit should be fixed to the wall with

suitable fixings

 Place heavier items on the lower shelves.

 Where possible heavier items should be evenly distributed across

the shelves.

3. CONTENTS

2. INTRODUCTION

Carefully unpack the product and check the contents (fig.1)

against the list below. Should any items be missing or damaged

make immediate contact with your Sealey dealer.

Part Description............................................................Quantity

A Upright Frame .............................................................................2

B Cross Beam (Long) .....................................................................8

C Wire Mesh Shelves .....................................................................4

D Cross Beam (Short) ..................................................................16

4. ASSEMBLY

4.1. We recommend that this shelving unit be assembled by two

people. The only tool required is a rubber mallet. DO NOT use a

hard faced hammer as this will damage the surface finish of the

cross beams. Make sure that all the clips lock in place securely

before using the unit. DO NOT use any parts that are damaged

and/or distorted. These may assemble incorrectly and result in

an installation that is unsafe, which may cause injury or

damage when the shelves are loaded.

Fig.1

4.2 See Fig.2. Support one end frame 'A' in a vertical position and

attach the end of one cross beam 'B' to it at the base of one of

the uprights. Ensure that both tags on the end bracket engage

properly with the slots in the upright as shown in the inset

diagram above. Tap the cross beam gently next to the end

bracket so that the beam is properly seated into the slots in the

upright. Connect the other end of the beam to the second end

frame at the same height and tap into place.

4.3 Attach another cross beam 'B' to the other side of the end frames

'A' ensuring that it is at the same level as the first cross beam.

Fully painted steel frame with four heavy-duty mesh shelves.

Industrial structured beams offers added strength with 800kg

capacity per level, giving a maximum capacity of 3200kg per

rack. Boltless design means no tools required to assemble.

Clips together in minutes. Suitable storage solution for workshop,

body shop, warehouse and agricultural environments.

Height: 1828mm Width: 1830mm Depth: 600mm

Fig.2

AP6572 & AP6572E ISSUE 5(A) 19/07/13

INCORPORATING EXTENSION PACK WITH 4 MESH SHELVES MODEL NO: AP6572E

IMPORTANT NOTE!

This unit has been third party tested to a max. load capacity of

800kg per shelf. It is important that the load is evenly distributed.

Please note that the cross beams will flex even before max. capacity

is reached. This is normal and the beams will return to their original

shape once load is removed.

Original Language Version

1 2 3

Summary of Contents

Page 1 - 800KG CAPACITY PER SHELF

INSTRUCTIONS FOR:RACKING UNIT WITH 4 MESH SHELVES 800KG CAPACITY PER SHELF MODEL NO: AP6572Thank you for purchasing a Sealey product. Manufactured to

Page 2 - Original Language Version

Attach 4 smaller cross beams 'D' between the main cross beams 'B'.4.4 See Fig.3. Continue to assemble the next two pairs of c

Page 3 - AP6572E

AP6572 & AP6572E ISSUE 5(A) 19/07/13EXTENSION PACKMODEL NO: AP6572E1.0 We recommend that this extension unit be assembled by two peo

Related models: AP6572E

Comments to this Manuals

No comments

Sealey AP6572 User Manual

Browse online or download User Manual for Equipment Sealey AP6572. Sealey AP6572 User Manual

Summary of Contents

Related models: AP6572E

Comments to this Manuals

Related products and manuals for Equipment Sealey AP6572