Sealey MK67 User Manual download pdf

INSTRUCTIONS FOR:

MASKING PAPER DISPENSER

MODEL:

MK67.V2

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly

maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

MK67.V2 Issue No: 1 - 26/08/08

 Ensure the dispenser is on a reasonably flat, level floor before loading.

 Be aware that the paper cutting blades are sharp, handle with care.

 DO NOT use the dispenser for any purpose other than that for which it is designed.

1. SAFETY INSTRUCTIONS

2. ASSEMBLY

ITEM PART NO. DESCRIPTION

1A&B MK66/01 FRAME

2 MK67/02 TRAY

3 MK67/03 BOTTOM PAPER BLADE

4 MK67/04 TOP PAPER BLADE

5 MK66/05 PAPER RETAINER

6 MK66/06 PAPER WASHER

7 MK66/07 SCREW

8 MK66/08 KNOB

9 MK67/09 PAPER BAR

10 MK66/10 NUT

11 MK66/11 WASHER

12 MK66/12 BOLT

13 MK67/13-B AXLE

14 MK67.V2-14 WHEEL

ITEM PART NO. DESCRIPTION

16 MK66/16 TIP FOOT

17 MK67/17 PAPER SPRING

20 MK66/20 TAPE REEL

21 MK66/21 HUB

22 MK66/22 BOLT

23 MK66/23 TOP TRAY

24 MK66/24 HANDLE GRIP

25 MK66/25 HANGER

27 MK66/27 RETAINING SPRING

28 MK66/28 KNOB OR WING NUTS

29 MK66/FK FIXING KIT(not shown)

30 MK67/15-B BOLT

31 MK67/29 WASHER

2.1 To assemble the side frames compress the silver

latch button at the top of the front leg 1B and insert

the tube into the back leg tube 1A until they snap

together. (See A in Fig.1).

2.2 Onto each end of the two paper bars 9 slide a large

retaining washer 6 followed by a retaining spring 27

followed by a black plastic retaining ring 5. Insert a

screw 7 into the threaded block on each retaining

ring.

2.3 Attach the side frames to each end of the paper bars

as shown in Fig.1 using the four black knobs 8.

2.4 Fit the bottom tray between the side frames and bolt

it to each leg using a bolt 22, a washer 11 and a nut

10.

2.5 Attach the upper paper blade 4 to the front of the

frame using two bolts 22, two washers 11 and two

nuts 10. (The upper blade has a wider profile than the

lower blade).

2.6 Attach the lower paper cutter 3 to the front of the

frame using two bolts 22, two washers 11 and two

nuts 10.

2.7 Attach a paper spring 17 to the back edge of each

paper cutter. Hook one end of the spring to the

notched back corner of the metalwork and stretch it

across and hook it to the other back corner. Take

care to avoid the paper cutter teeth when doing this.

2.8 To assemble the four tape reels as shown in fig.1

take a long bolt 12 and drop a washer 11 onto it

followed by a black plastic hub 21. Slide a reel 20

over the bolt and onto the hub ensuring that it is the

right way round. Retain the assembly using another

washer followed by a nut. After the nut has been

tightened the reel should still run freely on the hub.

Attach another nut to the bolt and insert the bolt

through the frame in one of the four places indicated

in Fig.1. Retain the assembly in place using a wing

nut 28 and a washer 11.

2.9 Attach the top tray 23 to the side of one of the frames

using two bolts 22, two washers 11 and two nuts 10.

The nuts and washers should be on the inside of the

tray.

2.10 Attach the hanger 25 to the side of the opposite

frame at the same level as the top tray. Insert the

ends of the hanger into the holes in the side of the

frame and tip the hanger forwards so that the first

bend in either end of the hanger is inside each frame

tube.

2.11 The dispenser has a tubular axle which allows an

axle bolt to be screwed into either end and also fixes

the axle to the frame. Slide a washer 31 over a bolt

30 followed by a wheel 14 and another washer 31.

Position the tubular axle 13 between the two rear

legs and pass the axle bolt through the rear leg and

screw it into the thread in the end of the axle. Attach

the other wheel in the same way. Tighten the axle

bolts until the wheel is lightly gripped then back off

slightly to allow the wheels to rotate.

Fig.1

1 2

Summary of Contents

Page 1 - MASKING PAPER DISPENSER

INSTRUCTIONS FOR:MASKING PAPER DISPENSERMODEL: MK67.V2Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if

Page 2 - 3. USING THE DISPENSERS

MK67.V23.1 Remove either the upper or lower paper bar from the frame by unscrewing and removing the black knobs at either end.3.2 Loosen the sc

Comments to this Manuals

No comments

Sealey MK67 User Manual

Browse online or download User Manual for Tools Sealey MK67. Sealey MK67 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Sealey MK67