Sealey AVR1500FP User Manual download pdf (Page 3)

7. MAINTENANCE

7.1 Before each use, check the vehicle lift to ensure it is not damaged or worn. If in any doubt DO NOT use the unit.

Remove it from service immediately and contact your local Sealey dealer for advice/repairs.

7.2 Refilling the hydraulic system with oil is rarely necessary but the level should be checked in the event of a loss of

performance. To check oil level, ensure the ram is fully lowered, remove filler plug and check that level is within10mm

of filler hole. Add

a good quality jack oil, such as SEALEY HYDRAULIC JACK OIL.

 WARNING: DO NOT use brake fluid, or any fluid other than hydraulic jack oil as this will cause serious damage

to the jack and will invalidate the warranty!

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534

sales@sealey.co.uk

Sole UK Distributor, Sealey Group,

Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk,

IP32 7AR

www.sealey.co.uk

Web

Original Language Version

6.1 Test run

6.1.1 Before each use, check the vehicle lift is functioning correctly and ensure it is not damaged or worn.

6.1.2 With the air line connected operate the lift valve to trial elevate, close the valve to stop. Lower the lift by operating the

hydraulic release valve pedal. If there is no air line, elevate by pumping the foot pedal. Lower the lift by operating the

hydraulic release valve pedal.

6.2 Lifting the vehicle

6.2.1 Lock, chock and handbrake vehicle wheels as required. Remove any objects left on the boot lid, bonnet and roof.

6.2.2 The vehicle lift assembly is mounted on four castors, two of which are swivel to enable precise alignment with the area

to be lifted. Handlebars mounted at shoulder height on the vertical pillar offers the assembly manouevrability.

6.2.3 Always start with the lift at its lowest position and decide whether a wheel or body lift is required. Fit the wheel cradle

adaptor or the body lift adaptor.

6.3 The wheel cradle adaptor

6.3.1 Check the tyres on the vehicle are correctly inflated.

6.3.2 With the wheel cradle adaptor hooked on to the elevator carriage, guide the cradle arms centrally and squarely toward

the target wheel.

6.3.3 The closer to the car body the better, provided the wheel registers fully on the parallel portion of the cradle arms.

6.3.4 With the air line connected operate the lift valve to trial elevate and then to the required height, close the valve to stop.

Alternatively if there is no air supply use the foot pump situated at the rear of the unit. Insert the safety stop bar at the

nearest position below the adaptor hook up block on the carriage and lower the lift by operating the hydraulic release

valve pedal until the load is taken by the stop bar.

6.4 The body lift adaptor

6.4.1 Check the tyres on the vehicle are correctly inflated.

6.4.2 An assessment must be made of the structural integrity of the vehicle jacking point. The body lift adaptor is designed

for body sill and seam engagement and a trial fitting by hand to the area to be lifted is recommended.

6.4.3 With the lift adaptor hooked on to the elevator carriage, guide the adaptor groove centrally and squarely toward the

vehicle jacking point seam.

6.4.4 With the air line connected operate the lift valve to trial elevate and then to the required height, close the valve to stop.

Alternatively if there is no air supply use the foot pump situated at the rear of the unit. Insert the safety stop bar at the

nearest position below the adaptor hook up block on the carriage and lower the lift by operating the hydraulic release

valve pedal until the load is taken by the stop bar.

5.1 Ensure the air supply valve (fig.2) is in the "Off" position before connecting to the air supply. The air/hydraulic lift

requires a minimum air pressure of **psi (*.*bar) to operate.

 WARNING! Ensure air supply is clean and does not exceed **psi (*.*bar). Too high an air pressure and

unclean air will shorten the life of the unit due to excessive wear, and may be dangerous causing possible

damage and/or personal injury.

5.2 Drain the air supply tank daily and clean the air

inlet filter screen weekly.

5.3 For recommended supply, see diagram to right.

5.4 Line pressure should be increased to

compensate for unusually long air hoses (over

8 metres).

5.5 Keep hose away from heat, oil and sharp edges.

Check hoses for wear and make certain that all

connections are secure.

5. AIR SUPPLY (IF AVAILABLE)

6. OPERATION

AVR1500FP Issue: 1 - 15/04/13

IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THIS PRODUCT.

Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.

DO NOT RETURN THE PRODUCT TO US. Please telephone us on 01284 757500 to obtain the address and phone number of your local

agent. If product is under guarantee please contact your dealer.

De-commissioning product

Should the product become completely unserviceable and require disposal, draw off the oil into an approved container and dispose of the

product and the oil according to local regulations.

Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to

www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500.

1 2 3

Comments to this Manuals

No comments

Conceptronic C10-696 Ficha de datos (3 paginas)

Marca: Conceptronic | Categoria: HDD/SSD enclosures | Tamaño: 0.22 MB |

Tabla de contenidos

CHD2MUB C20-252

Más productos y manuales para Hdd / ssd recintos Conceptronic

Modelos	Tipo de documento
C20-251	Ficha de datos Conceptronic 2,5" Harddisk Box Mini White USB powered, 3 paginas
C20-152	Ficha de datos Conceptronic 2,5" Harddisk Box Mini USB 3.0 USB powered, 3 paginas
C20-150	Ficha de datos Conceptronic 2,5" Harddisk Box USB 3.0 USB powered, 3 paginas
C20-258	Ficha de datos Conceptronic 2,5" Harddisk Box Mini Violet USB powered, 3 paginas
C05-210	Ficha de datos Conceptronic 3,5 inch USB hard disk box for SATA hard disk, 3 paginas
C05-500	Ficha de datos Conceptronic 2,5 / 3,5 inch hard disk docking station eSATA/USB, 3 paginas
CHD3SATA	Ficha de datos Conceptronic Serial ATA External Hard disk box 3.5 “., 1 paginas
C10-393	Ficha de datos Conceptronic Grab'n'GO 2.5” Hard Disk Box eSATA/USB 2.0, 3 paginas
C05-326	Ficha de datos Conceptronic USB SATA HDD 2.5" BLACK USB powered, 3 paginas
C10-135	Ficha de datos Conceptronic 3,5 inch USB/e-SATA hard disk box, 3 paginas
C05-106	Ficha de datos Conceptronic USB 2.0 & Firewire Harddisk Box 3.5", 1 paginas
C05-324	Ficha de datos Conceptronic 3,5 inch HardDiskBox DualBay, 3 paginas
C20-253	Ficha de datos Conceptronic 2,5" Harddisk Box Mini Blue USB powered, 3 paginas
C05-209	Ficha de datos Conceptronic 2,5 inch USB hard disk box for SATA hard disk, 3 paginas
CHD3U	Ficha de datos Conceptronic USB 2.0 Hard Disk Box 3.5", 1 paginas

Sealey AVR1500FP User Manual Page 3

Comments to this Manuals

Conceptronic C10-696 manuales

Conceptronic C10-696 Ficha de datos (3 paginas)

Tabla de contenidos

Más productos y manuales para Hdd / ssd recintos Conceptronic

Sealey AVR1500FP User Manual Page 3

Comments to this Manuals

Related products and manuals for Tools Sealey AVR1500FP

Conceptronic C10-696 manuales

Conceptronic C10-696 Ficha de datos (3 paginas)

Tabla de contenidos

Más productos y manuales para Hdd / ssd recintos Conceptronic