Sealey AUTOCHARGE12 User Manual download pdf

1.1. ELECTRICAL SAFETY

 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other

connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.

A Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current

Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected

by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.

You must also read and understand the following instructions concerning electrical safety.

1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances

and the safety of the appliance operators. If in any doubt about electrical safety, contact

a qualified electrician.

1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it

to the power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all

connections to ensure that none is loose.

1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply

to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7. DO NOT pull or carry the appliance by the power cable.

1.1.8. DO NOT pull the plug from the socket by the cable.

1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty

item repaired or replaced by a qualified electrician. When an ASTA/BS approved UK

3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.

Fit a new plug according to the following instructions (UK only).

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer insulation

extends beyond the cable restraint and that the restraint is tight.

Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.

To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.

1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure that

a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket with your

electrician.

1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance

plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that

the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the

use of 2.5mm² section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.

1.2. PERSONAL PRECAUTIONS

 Ensure there is another person within hearing range of your voice and close enough to come to your aid,

should a problem arise when working near a lead-acid battery.

 Wear safety eye protection and protective clothing. Avoid touching eyes while working near battery.

 Have fresh water and soap nearby in case battery acid contacts skin, clothing or eyes.

 Wash immediately with soap and water if battery acid contacts skin or clothing. If acid enters eye, flush eye immediately with cool, clean

running water for at least 15 minutes and seek immediate medical attention.

 Remove personal metallic items such as rings, bracelets, necklaces and watches. A lead-acid battery can produce a short-circuit current

which is high enough to weld a ring or the like to metal, which would cause severe burns.

 Ensure hands, clothing (especially belts) are clear of fan blades and other moving or hot parts of engine, remove ties and contain long hair.

 DO NOT smoke or allow a spark or flame in the vicinity of battery or engine.

1.3. GENERAL SAFETY INSTRUCTIONS

 Familiarise yourself with the application and limitations of the charger as well as the potential hazards. Also refer to the vehicle

manufacturer’s hand book. IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.

 Ensure the charger is in good order and condition before use. If in any doubt do not use the unit, contact your Sealey Dealer.

 Only use recommended parts. The use of unauthorised parts may be dangerous and will invalidate your warranty.

 Use the charger in the upright position only and ensure it is placed on a stable surface which will adequately support its weight.

 Ensure the charger is disconnected from the mains supply before attaching/detaching the power clamps to/from the battery.

 Keep tools and other items away from the engine and ensure you can see the battery and working parts of engine clearly.

INSTRUCTIONS FOR:

ELECTRONIC BATTERY

CHARGERS

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give

you years of trouble free performance.

1. SAFETY INSTRUCTIONS

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.

USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

DANGER! BE AWARE, LEAD-ACID BATTERIES GENERATE EXPLOSIVE GASES DURING NORMAL BATTERY OPERATION. FOR THIS

REASON, IT IS VERY IMPORTANT TO READ AND FOLLOW THESE INSTRUCTIONS CAREFULLY, EACH TIME YOU USE THE CHARGING

EQUIPMENT.

Follow these instructions and those published by the battery and vehicle manufacturers, and the maker of any equipment you

intend to use in the vicinity of the battery. Remember to review warning marks on all products and on engines.

FUSE RATING

3 AMP

Blue

Neutral

Wire

Yellow & Green

Earth Wire

Cable

Restraint

Brown

Live

Wire

AUTOCHARGE6.V4 AUTOCHARGE9 AUTOCHARGE12.V4

Original Language Version

AUTOCHARGE6.V4, AUTOCHARGE9, AUTOCHARGE12.V4 Issue: 3 - 10/09/10

1 2 3

Summary of Contents

Page 1 - CHARGERS

1.1. ELECTRICAL SAFETY WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:You must c

Page 2 - 3. OPERATION

2.1. Introduction Compact electronic battery chargers with pressed steel casings and carrying handle. Intelligent charge control and selectable slow

Page 3 - 01284 703534

3.2. BATTERY CHARGING: WARNING! Ensure you read, understand and follow all safety instructions in Section 1 before attempting to use the AUTO

Related models: AUTOCHARGE9 | AUTOCHARGE6 |

Comments to this Manuals

No comments

Sealey AUTOCHARGE12 User Manual

Browse online or download User Manual for Power suppliers Sealey AUTOCHARGE12. Sealey AUTOCHARGE12 User Manual

Summary of Contents

Related models: AUTOCHARGE9 | AUTOCHARGE6 |

Comments to this Manuals

Related products and manuals for Power suppliers Sealey AUTOCHARGE12