1.1. PERSONAL PRECAUTIONS.
When using the test leads, observe all normal safety rules concerning:
Protection against the dangers of electric current.
Protection of the test leads against misuse.
DO NOT use leads if damaged or if the internal wire is exposed in
any way.
1.2. GENERAL SAFETY INSTRUCTIONS.
WARNING! Never perform resistance measurements on live circuits.
Only measure on disconnected circuits.
These test leads are designed to be used on automotive circuits only.
DO NOT use on 110V and 230V applications.
Familiarise yourself with the application and limitations of the test
leads as well as the potential hazards.
IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.
When not in use, store the test leads in the case supplied.
Keep the work area clean, uncluttered and ensure there is adequate
lighting. Keep tools and other items away from the engine and ensure
that you can see the working parts of the engine clearly.
Observe standard workshop safety procedures when using the test
leads.
Consult the vehicle's handbook for fuse positions and check if the fuse
hasblown.Ifthefusehasblown,rstestablishthereasonforthis
before replacing with the same fuse type.
Ensure test leads are kept clear of hot surfaces and rotating parts.
Never apply voltage or current to the test leads that exceeds the
specified maximum.
DO NOT use the test leads for any purpose other than for which they
are designed.
DO NOT get the test leads wet, or use in damp or wet locations or
areas where there is condensation.
INSTRUCTIONS FOR:
TEST LEAD KIT 92PC
MODEL No: TA111.V2
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained,
give you years of trouble free performance.
1. SAFETY INSTRUCTIONS
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. PLEASE KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
2. INTRODUCTION
Comprehensive set of test leads and components suitable for testing,
isolating and evaluating automotive electronic circuits. Kit includes standard
Ø4mm banana style plugs and sockets suitable for use with most diagnostic
multimeters and test equipment. Supplied in sectioned carry-case for quick
location of components.
TA111.V2 ISSUE No:1 07/06/13
3. CONTENTS
3.1. FLAT TERMINALS (fig.1)
0.7mm (Male/Female) + Female banana sockets (3pcs each)
0.8mm (Male/Female) + Female banana sockets (3pcs each)
1.2mm (Male/Female) + Female banana sockets (3pcs each)
2.0mm (Male/Female) + Female banana sockets (3pcs each)
2.5mm (Male/Female) + Female banana sockets (3pcs each)
3.0mm (Male/Female) + Female banana sockets (3pcs each)
5.0mm (Male/Female) + Female banana sockets (3pcs each)
6.0mm (Male/Female) + Female banana sockets (3pcs each)
fig.1
fig.2
3.2. ROUND TERMINALS (fig.2)
1.5mm (Male/Female) + Female banana sockets (3pcs each)
2.0mm (Male/Female) + Female banana sockets (3pcs each)
3.5mm (Male/Female) + Female banana sockets (3pcs each)
4.0mm (Male/Female) + Female banana sockets (3pcs each)
Both flat and round terminals are available as shown below. Each male or
female connector is attached to a short lead with a 4mm banana socket at
the other end. Each lead is supplied in quantities of 3, other connectors
are shown overleaf.
Original Language Version
© Jack Sealey Limited
(2 pages)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals