Sealey HVD24 User Manual download pdf

INSTRUCTIONS FOR:

INDUSTRIAL HIGH VELOCITY FANS

MODEL NO'S: HVD24.V2, HVD30.V2, HVD36.V2

1.1. ELECTRICAL SAFETY

 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:

You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other

connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices. A

Residual Current Circuit Breaker (RCCB) should be incorporated in the main distribution board. We also recommend that a Residual Current

Device (RCD) is used. It is particularly important to use an RCD with portable products that are plugged into a supply which is not protected

by an RCCB. If in any doubt consult a qualified electrician. You may obtain a Residual Current Device by contacting your Sealey dealer.

You must also read and understand the following instructions concerning electrical safety.

1.1.1. The Electricity at Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible

for the safe condition of those appliances and the safety of the appliance operators. If in

any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it

to the power supply. See 1.1.1. and 1.1.2. and use a Portable Appliance Tester.

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Regularly inspect power supply cables and plugs for wear or damage and check all

connections to ensure that none is loose.

1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply

to be used and that the plug is fitted with the correct fuse - see fuse rating at right.

1.1.7. DO NOT pull or carry the appliance by the power cable.

1.1.8. DO NOT pull the plug from the socket by the cable.

1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty item repaired or replaced by a qualified

electrician. When an ASTA/BS approved UK 3 pin plug is damaged, cut the cable just above the plug and dispose of the plug safely.

Fit a new plug according to the following instructions (UK only).

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all wires have been correctly connected, that the cable outer

insulation extends beyond the cable restraint and that the restraint is tight.

Double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.

To rewire, connect the wires as indicated above - DO NOT connect either wire to the earth terminal.

1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure

that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket

with your electrician.

1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an RCD fitted is preferred since any appliance

plugged into it will be protected. The cable core section is important and should be at least 1.5mm², but to be absolutely sure that

the capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the

use of 2.5mm² section cable. If extension reel is to be used outdoors, ensure it is marked for outdoor use.

RECOMMENDED FUSE RATING

HVD24.V.2 3AMP,

HVD30.V2 & HVD36.V2 5AMP.

1.2. GENERAL SAFETY

 Disconnect the fan from the mains power when not in use and before servicing or performing any maintenance.

 Use the fan in dry areas only. DO NOT use in wet or areas with high condensation such as showers, pools etc.

 WARNING! If a fan falls into water or other liquid, immediately switch off and disconnect from the mains power supply. DO NOT

touch the fan until the mains power supply has been disconnected.

 Always disconnect the fan from the power supply when moving it from one location to another and ensure fan is stood on a level

surface.

 The fan air flow is powerful. Before use ensure that there is nothing nearby that will be damaged or displaced by the stream of air.

 Keep the fan clean and maintained in good condition. For motor service contact an authorised service agent.

 Use recommended parts only. Unapproved parts may be dangerous, and will invalidate your warranty.

 DO NOT operate the fan where there are explosive or flammable gases, fumes or other hazardous substances.

 DO NOT stand the fan on the power cable.

 DO NOT insert any objects through the fan guard.

 DO NOT cover the fan when in use.

 DO NOT immerse the fan in water or any other liquid.

 DO NOT allow children to operate the fan.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT

CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL

INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

HVD24.V2, HVD30.V2 & HVD36.V2 Issue: 4 (SP) - 02/12/14

Original Language Version

1. SAFETY

Refer to instruction

manual

1 2

Summary of Contents

Page 1 - HVD24.V2, HVD30.V2, HVD36.V2

INSTRUCTIONS FOR: INDUSTRIAL HIGH VELOCITY FANSMODEL NO'S: HVD24.V2, HVD30.V2, HVD36.V21.1. ELECTRICAL SAFETY WARNING! It is the responsibilit

Page 2 - WEEE Regulations

Model No.: ......... HVD24.V2 ....... HVD30.V2 .........HVD36.V2Fan Diameter: ...

Related models: HVD30 | HVD36 |

Comments to this Manuals

No comments

Sealey HVD24 User Manual

Browse online or download User Manual for Fans Sealey HVD24. Sealey HVD24 User Manual

Summary of Contents

Related models: HVD30 | HVD36 |

Comments to this Manuals

Related products and manuals for Fans Sealey HVD24