Sealey WL483D User Manual download pdf

1.1. ELECTRICAL SAFETY

 WARNING! It is the user’s responsibility to read, understand and comply with the following:

You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and

all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety

devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD

(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products that are plugged

into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by

contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.

1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance

and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains

power supply. See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Regularly inspect power supply, leads, plugs for wear and damage and all electrical connections to

ensure that none is loose.

1.1.6. Important: Ensure that the product voltage matches the power supply to be used.

1.1.7. DO NOT pull power plugs from sockets by the power cable.

1.1.8. DO NOT use worn or damaged leads, plugs or connections. Immediately replace or have repaired by

a qualified electrician. A U.K. 3 pin plug with ASTA/BS approval is fitted.

In case of damage, remove and fit a new plug according to the following instructions (discard old

plug safely). (UK only - see diagram at right).

Ensure the unit is correctly earthed via a three-pin plug.

a) Connect the green/yellow earth wire to the earth terminal ‘E’.

b) Connect the brown live wire to live terminal ‘L’.

c) Connect the blue neutral wire to the neutral terminal ‘N’.

d) After wiring, check that there are no bare wires, that all wires have been correctly

connected, that cable outer insulation extends beyond the cable restraint and that the restraint is tight.

Powerful 3 diopter 120mm precision lens gives high quality magnifying capabilities. Features 48 SMD LEDs to illuminate the object for

improved detailed work. Multi-position swing arm allows simple positioning of lamp to suit task. Features a G-clamp base to secure to a

workbench or table. Ideal for electrical engineers, engravers and fine detail work.

Original Language Version

WL483D Issue No.1 01/05/14

RECOMMENDED

FUSE RATING: 3AMP

Model No: .............................................WL483D

LEDs: .....................................................48 SMD

Supply:...................................................230V

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE

PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR

PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these

instructions, and properly maintained, give you years of trouble free performance.

1. SAFETY

2. INTRODUCTION

3. SPECIFICATION

4. OPERATION

g.1

g.2

INSTRUCTIONS FOR:

BENCH MOUNTED WORK LIGHT

48 SMD LED

MODEL NO: WL483D

4.1. Mounting

4.1.1. Fixtheclamptoasecuresurface.Seeg.1.

4.1.2. Lower the work light assembly into the clamp, use two

hands to prevent the lamp moving during this operation.

4.1.3. Turnon/offusingtheswitchontop.Seeg.2.

4.1.4. Adjust by loosening/tightening the head clamp. See

 g.3.

Note: Be aware of the effect of using the lamp close to a

window/door where it could be in direct sunlight.

Remember to close the lid on top whilst it is not in use.

1 2

Summary of Contents

Page 1 - 48 SMD LED

1.1. ELECTRICAL SAFETY  WARNING! It is the user’s responsibility to read, understand and comply with the following:You must check all electrical e

Page 2 - 01284 703534

WL483D Issue No.1 01/05/14 Environmental ProtectionRecycle unwanted materials instead of disposing of them as waste. All tools, accessories and pac

Comments to this Manuals

No comments

Sealey WL483D User Manual

Browse online or download User Manual for Tools Sealey WL483D. Sealey WL483D User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools Sealey WL483D