Sealey GDM1630FR User Manual download pdf

1. SAFETY INSTRUCTIONS

1.1. ELECTRICAL SAFETY.

p WARNING! It is the user’s responsibility to read, understand and comply with the following:

You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and

all electrical connections for wear or damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety

devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD

(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products that are plugged

into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by

contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.

1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by

a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances

and the safety of appliance operators. If in any doubt about electrical safety, contact a qualified electrician.

1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power supply.

See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).

1.1.4. Ensure that cables are always protected against short circuit and overload.

1.1.5. Regularly inspect power supply leads and plugs for wear or damage and connections to ensure

that none is loose.

1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power

supply to be used, and check that plugs are fitted with the correct capacity fuse. A 13 amp plug

may require a fuse smaller than 13 amps for certain products.

1.1.7. DO NOT pull power plugs from sockets by the power cable.

1.1.8. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have

repaired by a qualified electrician. Where a U.K. 3 pin plug with ASTA/BS approval is fitted, in

case of damage, cut off and fit a new plug according to the following instructions (discard old

plug safely).

(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.

a) Connect the GREEN/YELLOW earth wire to the earth terminal ‘E’.

b) Connect the BROWN live wire to the live terminal ‘L’.

c) Connect the BLUE neutral wire to the neutral terminal ‘N’.

After wiring, check there are no bare wires, that all wires have been correctly connected, that the cable outer insulation

extends past the cable restraint and that the cable restraint is tight.

Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always

marked with this symbol . To re-wire, connect the brown & blue wires as indicated above. DO NOT connect the brown or blue

wires to the earth terminal.

1.1.9. NOTE: If this product requires more than a 13 amp electrical supply, then NO plug is fitted. You must therefore contact a qualified

electrician to ensure a 30 amp fused supply is available. We recommend you discuss the installation of a industrial round pin plug and

socket with your electrician.

1.1.10. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD

fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cores in the cable

is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the cable reel is suitable for this product and

for any that may be used in the other output sockets, the use of 2.5mm² section is recommended.

Blue

Neutral

wire

Yellow & Green

Earth wire

Cable

restraint

REPLACEMENT FUSES MUST

BE OF THE SAME TYPE AND

RATING AS THE ORIGINAL

Brown

Live

wire

INSTRUCTIONS FOR:

RADIAL PILLAR DRILLS

MODEL No's: GDM790BR & GDM1630FR

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions

and properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND

CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY

CAUSE DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

1.2. GENERAL SAFETY

p WARNING! Disconnect drill from mains power before changing accessories, servicing or performing

any maintenance.

3 Maintain the drill in good condition (use an authorised service agent).

p WARNING! Keep all guards and holding screws in place, tight and in good working order. Check regularly

for damaged parts. A guard or any other part that is damaged must be repaired or replaced before

the tool is next used, to ensure that it will operate properly and perform its intended function. The safety

guard is a mandatory fitting where drill is used in premises covered by the Health & Safety at Work Act.

3 Check alignment of moving parts and check for possible broken parts.

3 Replace or repair damaged parts. Use genuine Sealey parts only. Non-authorised parts may be dangerous

and will invalidate the warranty.

3 Ensure the set screws of the head frame are screwed tight before using the drill.

3 Secure the drill to the bench/floor to avoid the machine tipping, sliding or walking. Drill is designed for use with

drill bits only. No other accessory may be used.

3 Ensure the chuck is securely fastened to the spindle.

3 Remove adjusting keys and wrenches from the machine and working area before switching on.

3 Use clamps or a vice (not included) to secure the workpiece. Available from your Sealey dealer. DO NOT

secure the workpiece by hand.

Original Language Version

GDM790BR, GDM1630 Issue: 4 - 23/03/10

1 2 3 4 5

Summary of Contents

Page 1 - GDM790BR & GDM1630FR

1. SAFETY INSTRUCTIONS1.1. ELECTRICAL SAFETY. p WARNING! It is the user’s responsibility to read, understand and comply with the following:You mus

Page 2 - 4. CONTENT

3 Refer to speed chart for recommended drilling speeds.p WARNING! Always wear approved eye or face protection when operating this drill. Use a dust

Page 3 - Original Language Version

p WARNING! Ensure the drill is unplugged from the mains power supply before commencing. 6.1. Installing drill bit6.1.1. Insert drill bit in

Page 4

6.6. Setting the drill depth 6.6.1. Use the scale on the side of the drill head near the drill handle. 6.6.2. Loosen locking screw (36) and set the

Page 5 - 8. MAINTENANCE

9. TROUBLESHOOTING8.1. Clean the drill after each use. A coat of automobile-type wax applied to the table and column will help to keep the surface

Related models: GDM790BR | GDM140F | GDM92B | PDM125B | PDM155B | GDM150B | GDM180B | GDM200F | PDM170F | PDM210F | PDM240F | PDM260F | GDM120B | GDM160F |

Comments to this Manuals

No comments

Sealey GDM1630FR User Manual

Browse online or download User Manual for Tools Sealey GDM1630FR. Sealey GDM1630FR User Manual

Summary of Contents

Related models: GDM790BR | GDM140F | GDM92B | PDM125B | PDM155B | GDM150B | GDM180B | GDM200F | PDM170F | PDM210F | PDM240F | PDM260F | GDM120B | GDM160F |

Comments to this Manuals

Related products and manuals for Tools Sealey GDM1630FR