Sealey 57M User Manual download pdf

Manufactured to German GS/TUV standards. Fine rolled threading and precision made thrust

bearing for long life and smooth operation. Curved base plate allows for radial movement when

lifting vehicle.

Model No. 57M.V2 58M

Maximum height ......330mm ..........375mm

Minimum height ...... 85mm ..........100mm

Closed length ........365mm ..........405mm

Capacity . . . . . . . . . . . .1000kg ..........1500kg

INSTRUCTIONS FOR:

SCISSOR JACK

MODEL NO’s: 57M.V2 & 58M

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL

REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE

PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL

INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

3 Ensure that the jack is in good working order. Take action for immediate repair or

replacement of damaged parts. Use genuine parts only. The use of unauthorised

parts may be dangerous and will invalidate the warranty.

3 Locate the jack in a suitable, well lit work area.

3 Keep work area clean and tidy and free from unrelated materials.

3 Use jack on level and solid ground, preferably concrete. Avoid tarmacadam as jack may sink in.

3 Ensure the vehicle handbrake is engaged, engine/motor is switched off and

transmission is in 1st or reverse gear. (or park for automatics)

3 Ensure minimum distance of 0.5m between vehicle and static objects such as doors,

walls, etc., to allow for vehicle tilting.

3 Only place jack under those lifting points recommended by the vehicle manufacturer

(see vehicle handbook).

3 Check the lifting point is stable and centred on the jack saddle.

3 Ensure there are no passengers in the vehicle.

3 Place wedges under wheels of vehicle.

3 Ensure all non-essential persons keep a safe distance whilst the jack is in use.

3 Use suitable capacity axle stands under the vehicle before proceeding with any task.

3 Ensure there are no persons or obstructions beneath the vehicle before lowering.

p DANGER: Use the jack for lifting only, NOT for supporting the lifted load.

7 DO NOT operate the jack if damaged.

7 DO NOT work under the vehicle until axle stands have been correctly positioned.

7 DO NOT allow untrained persons to operate the jack.

7 DO NOT use the jack for purposes other than that for which it is designed.

7 DO NOT exceed the rated capacity of the jack.

7 DO NOT jack vehicle if there is a risk of spillage of fuel, battery acid, or other dangerous

substances.

7 DO NOT allow the vehicle to move while supported by the jack.

3 When not in use store jack, fully lowered, in a safe, dry, childproof area.

p WARNING! It is very dangerous to go under a vehicle which is supported by a jack

even if additional supports are used. DO NOT go under a vehicle unless it is

supported by adequately rated axle stands.

IMPORTANT! Ensure that you can see the saddle and jacking point throughout the

jacking operation in case there is any relative movement.

2. INTRODUCTION & SPECIFICATIONS

1. SAFETY INSTRUCTIONS

Original Language Version

57M.V2, 58M Issue: 4 - 14/10/09

1 2

Summary of Contents

Page 1 - 57M.V2 & 58M

Manufactured to German GS/TUV standards. Fine rolled threading and precision made thrust bearing for long life and smooth operation. Curved base plate

Page 2 - 01284 703534

3.1. General jacking. p WARNING! Before lifting ensure Section 1 safety instructions are strictly followed. 3.1.1. Prepare the vehicle as mentione

Related models: 58M

Comments to this Manuals

No comments

Sealey 57M User Manual

Browse online or download User Manual for Tools Sealey 57M. Sealey 57M User Manual

Summary of Contents

Related models: 58M

Comments to this Manuals

Related products and manuals for Tools Sealey 57M