Sealey E5188 User Manual download pdf (Page 2)

3.1. Connection

3.1.1. Ensure that the ON/OFF switch is in the OFF

position before connecting to the mains supply.

Refer to fig.1a,‘OFF’ is shown as ‘0’ on the switch.

3.2. Fitting Accessories Direct to Rotary Tool

3.2.1. Ensure that the tool is switched OFF.

3.2.2. Press the spindle lock button, refer to fig.1, and

slowly turn the collet until the spindle lock engages.

3.2.3. Retain the pressure on the spindle lock button

and turn the collet nut anti-clockwise to open

the collet.

NOTE: Never press the spindle lock button when the tool is running.

3.2.4. The required bit may now be fitted into the collet. Fully insert the bit shaft to reduce the risk of bending in use. Tighten the collet nut

firmly using the spanner supplied. Finally, release the spindle lock button.

3.2.5. To change collet, proceed as 3.2.1 to 3.2.3 but continue to unscrew the collet nut until it can be removed from the spindle. Change

collet and replace the collet nut.

3.2.6. Select the speed required on the variable speed control. Small accessories require high speed and large accessories

low speed. If in doubt, start on a low setting and gradually increase speed until best performance is obtained.

3.2.7. Check that the ON/OFF switch is OFF and then connect the tool to the mains power supply.

Turn the ON/OFF switch to ON.

DO NOT switch ON with the tool bit touching the workpiece. Always allow

the bit to reach full speed before applying it to the workpiece.

3.3. Attaching Flex Drive and Bits.

Ensure that the tool is switched OFF and remove plastic collar (fig.1).

3.3.1. Press the spindle lock button, refer to fig.1 or fig.2A, and slowly turn the collet

nut until the spindle lock engages.

3.3.2. Retain the pressure on the spindle lock button and turn the collet nut anti-clockwise to loosen the collet.

3.3.3. Extract the flex drive from the centre of the shaft (fig.2B).

3.3.4. Insert the flex drive into the collet inside the spindle nut and tighten by holding in the spindle locking button and

tighten with the spanner.

3.3.5. Slide the flex drive back up into the shaft and secure by screwing the rotary shaft connector onto the rotary tool

(fig.2).

3.3.6. At the other end of the flex drive shaft insert the locking pin into the outer casing (fig.3), it may be necessary to

rotate the collet nut to align the holes, once the shaft is locked, turn the collet nut anti-clockwise to loosen.

3.3.7. If necessary replace the collet with one the correct size for the task at hand.

3.3.8. Replace the collet nut and insert a bit. Tighten the collet nut firmly and remove the locking pin.

3. OPERATION

Supply:.......................230V, 170W

Speed Range:. ...........8000 to 35000rpm

Speed Settings:. ............Stepless Control

Collet Sizes: .........1.5mm, 2.3mm, 3.2mm

Noise Power: ....................84dB(A)

Noise Pressure: ..................73dB(A)

2. SPECIFICATION

4. MAINTENANCE

4.1. Cleaning

4.1.1. Keep the tool's ventilation slots clean and free from obstructions. If available, blow compressed air into the vents to clear any

internal dust (safety goggles must be worn when undertaking this process).

4.1.2. Keep the outer case of the tool clean and free from grease.

4.1.3. Wipe down with a damp cloth. DO NOT wash with water or use solvents or abrasives.

4.2. Servicing

To service the tool contact your local Sealey service agent.

fig.2

fig.1

NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.

IMPORTANT: No liability is accepted for incorrect use of this product.

WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.

INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.

01284 757500

01284 703534

sales@sealey.co.uk

Sole UK Distributor, Sealey Group,

Kempson Way, Suffolk Business Park,

Bury St. Edmunds, Suffolk,

IP32 7AR

www.sealey.co.uk

Web

Original Language Version

E5188.V4 Issue:2(SP)-21/03/14

fig.1a

Parts support is available for this product. To obtain a parts listing and/or diagram,

please log on to www.sealey.co.uk, email sales@sealey.co.uk or telephone 01284 757500.

Environmental Protection

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be

sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment.

WEEE Regulations

Dispose of this product at the end of its working life in compliance with the EU Directive on

Waste Electrical and Electronic Equipment (WEEE). When the product is no longer required, it must be disposed

of in an environmentally protective way. Contact your local solid waste authority for recycling information.

fig.3

1 2 3

Comments to this Manuals

No comments

Sealey E5188 User Manual Page 2

Comments to this Manuals

Related products and manuals for Power tools Sealey E5188