Sealey AK433 User Manual download pdf

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

INSTRUCTIONS FOR:

RECHARGEABLE LANTERN

MODEL No: AK433.V2

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you

years of trouble free performance.

1. SAFETY INSTRUCTIONS

1.1. GENERAL SAFETY

 Ensure the lantern is charged for a minimum of 15 hours before initial use.

 DO NOT charge the battery for more than 20 hours. Explosive gas will be

generated if overcharged.

 DO NOT charge the battery if the ambient temperature is greater than

40°C or less than 5°C.

 WARNING! The lens may become hot after prolonged use.

 DO NOT cover or block the lens during use.

 DO NOT turn the lantern on when it is being charged.

 DO NOT shine directly into your, other person’s or animal’s eyes.

 DO NOT stand the lantern near any surface or item that may be adversely

affected by the heat emitted from the lens.

 DO NOT allow children to use the lantern.

 DO NOT handle or move the lantern whilst it is being charged.

 DO NOT use the lantern if you suspect that the battery or the lantern

casing is damaged.

 Ensure that correctly rated battery and bulb are used for replacements.

 When not in use store the lantern in a safe, dry, childproof location.

 DO NOT dis-assemble the battery for any reason.

 DO NOT leave battery in a discharged state, recharge battery immediately.

If the lantern is not in use, recharge the battery every three months.

 Dispose of the old battery in accordance with local authority regulations.

 DO NOT dispose of with regular refuse.

1.2. ELECTRICAL SAFETY

USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING THE

LANTERN TO THE MAINS POWER SUPPLY.

USE ONLY THE SUPPLIED ADAPTOR LEAD FOR CONNECTING THE

LANTERN TO A VEHICLE'S 12V ACCESSORY SOCKET.

 WARNING! It is the owner’s responsibility to read, understand and comply

with the following electrical instructions:

You must ensure the risk of electric shock is minimised by the installation

of appropriate safety devices. An RCCB (Residual Current Circuit Breaker)

should be incorporated in the main distribution board. We also recommend

that an RCD (Residual Current Device) is used with all electrical products,

particularly portable equipment which is plugged into an electrical supply

not protected by an RCCB.

You must also read and understand the following instructions concerning

electrical safety.

1.2.1. The Electricity At Work Act 1989 requires all portable electrical

appliances, if used on business premises, to be tested by a qualified

electrician, using a Portable Appliance Tester (PAT), at least once a year.

1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical

appliances responsible for the safe condition of the appliance and the

safety of the appliance operator. If in any doubt about electrical safety,

contact a qualified electrician.

1.2.3. You must ensure that you:

 Inspect the charger plug, cable and connector for wear and damage to

ensure items are safe before connecting to the mains power supply.

If worn or damaged DO NOT use.

 Check cables are always protected against short circuit and overload.

 Important: Check that the voltage marked on the charger plug is the same

as the power supply to be used.

 Uncoil the cable between charger and the lantern.

 DO NOT pull the charger plug from the mains socket by the lead.

 DO NOT use any other type of charger with this product.

 DO NOT place the connector into any area of the lantern except the

correct jack inlet socket.

 DO NOT try to take the charger plug apart.

 DO NOT use the charger plug to charge or power any other electrical item.

 DO NOT get the charger wet, or use in wet, damp conditions (for indoor

use only).

 WARNING!NEVER substitute a standard 13 amp 3 pin plug, or any other

type of plug, for the charger plug.

2. INTRODUCTION & SPECIFICATIONS

3. CHARGING

2.1. INTRODUCTION

Lantern with swivel handle feature allowing pistol grip or carry handle

operation. Ø85mm lens with 1W CREE LED bulb produces 3-million

candlepower lasting up to 3hrs on one charge. Secondary side LED tube

light, with low power consumption lasts up to 24hrs on full charge. Suitable

for a wide variety of applications. Supplied with 4V 1Ah sealed battery,

in-car charger and 230V mains charger.

 WARNING! Ensure that you read, understand and apply the safety

instructions relating to the battery and charger before use.

 IMPORTANT: Turn off lantern while charging. Failure to do so will

damage the charger plug/vehicle plug.

 IMPORTANT WARRANTY INFORMATION:

The battery fitted to this lantern is considered to be a consumable item and

its ability to accept charge will reduce over time. We will warranty it against

mechanical and electrical defect for a period of one year - this does not

cover fair wear and tear. If the battery is not properly charged before first

use, or regularly conditioned, its capacity will diminish. Under these

circumstances we will not replace the battery even if it is less than one

year old.

3.1. CHARGER PLUG - AK433.V2.CA

3.1.1. The charging jack plug socket is situated beneath the switch (fig.1B).

Fully insert the jack plug and stand the lantern in a safe location ready to

charge.

3.1.2. Ensure the lantern is turned off and then plug the charger into the mains

supply and switch on. The red LED (fig.1C) will light up to indicate that

charging is in progress.

3.1.3. Allow 15 hours for charging. When fully charged, switch off the

mains supply and unplug the charger. Remove the charger jack plug from

the lantern.

3.1.4. Store the charger in a safe, dry childproof location.

Notes: a) A fully charged battery will last for approximately 3 hours on main

torch and 24 hours on side tube LED.

b) There is no need to fully discharge the battery before recharging.

3.2. VEHICLE ADAPTOR LEAD

3.2.1. The charging jack plug socket is situated beneath the switch (fig.1B).

Fully insert the jack plug and stand the lantern in a safe location ready to

charge.

3.2.2. Ensure the lantern is turned off and then plug the charger into the vehicle's

12V accessory socket. The red LED (fig.1C) will light up to indicate that

charging is in progress.

3.2.3. When fully charged, unplug the adaptor from the vehicle socket and

from the lantern before turning the lantern on.

3.2.4. Store the adaptor in a safe, dry, childproof location.

NOTE: Charging the lantern from a 12 volt vehicle socket may drain the vehicle

battery.

Original Language Version

AK433.V2 Issue: 1 - 22/02/12

fig.1

2.2. SPECIFICATIONS

Lens............ 85mm

Cell Type ........ 4V - 1Ah Rechargeable

Operating Time ... 3hrs / 24hrs

Charge Time ..... 15hrs

1 2

Summary of Contents

Page 1 - AK433.V2

IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY AND WIT

Page 2 - 4. OPERATION

fig. 6NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts withou

Comments to this Manuals

No comments

Sealey AK433 User Manual

Browse online or download User Manual for Lighting Sealey AK433. Sealey AK433 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Sealey AK433