Sealey HBS2001 User Manual download pdf

The SEALEY BODYSHOP/WORKSHOP HEADLAMP BEAM SETTER, HBS2001, is supplied with a fixed column, mirror and visor. This

HEADLAMP BEAM SETTER may be used for checking headlights on cars, heavy goods vehicles and motorcycles.

SPECIFICATION: Height . . . . . . .1750mm Maximum height of beam measurement . . . . . . .1500mm

Width . . . . . . . . .620mm Minimum height of beam measurement . . . . . . . .220mm

Length . . . . . . . .660mm Focal length . . . . . . . . . . . . . . . . . . . . . . . . . . . . .500mm

Refer to fig. 1

A BASE

B COLUMN

C VERTICAL SLIDING SYSTEM

2.1. Attach column B to base A using nuts, bolts and washers provided.

Column should be positioned so that optical system mounting plate on

sliding system C is facing the single wheel.

2.2. Attach mirror-visor D to mounting plate at the top of column B with the

two screws provided (in end of visor).

2.3. Fit the optical system E to the vertical sliding system C using the two

screws and washers provided (fit lever screw F and larger washer over

slotted hole).

HBS2001 - 2 - 061103

1. DESCRIPTION

2. ASSEMBLY

3. WORKING SURFACE

3.1.

Position the vehicle on the designated headlamp aim standing area.

3.2. When positioning the HBS ensure the floor is perfectly even and level.

3.3.

If this is not possible the vehicle and HBS must be on the same slope, which must not exceed 0.5º.

3.4. Headlights must not be checked where surface angle exceeds 0.5º (see fig. 2).

fig. 2

fig. 1

NO NO0.5

MAX

GENERAL RULES

Read instruction manual carefully before using the headlamp beam setter (HBS).

TO AVOID DAMAGE ENSURE THE FOLLOWING ARE STRICTLY APPLIED.

DO NOT allow unqualified persons to operate the HBS.

DO NOT use the HBS in direct sunlight.

DO NOT splash the HBS with water or any other liquid.

DO ensure the work area is well ventilated.

DO ensure that there is good lighting.

DO apply handbrake on vehicle.

DO avoid sudden changes in temperature.

DO avoid sudden vibration.

INSTRUCTIONS FOR:

BODYSHOP/WORKSHOP HEADLAMP

BEAM SETTER Model:

HBS2001

Thank you for purchasing a Sealey Product. Manufactured to a high standard this product will, if used according to these instructions and

properly maintained, give you years of trouble free performance.

4. 1. Straighten vehicle wheels.

4. 2. Check the tyre pressures.

4. 3. Ensure the headlights are clean and dry.

4. 4. If the vehicle is fitted with manual or electric headlamp levelling device, ensure this is set for vehicle with normal load.

4. 5. Remove anything which could alter the attitude of the vehicle, i.e. load, snow

, ice, mud, etc.

4. VEHICLE PREPARATION

IMPORTANT

PLEASE READ THESE INSTRUCTIONS CAREFULL

Y. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.

USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE

DAMAGE

AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.

D MIRROR-VISOR

E OPTICAL SYSTEM

F LEVER SCREW

1 2 3 4 5 6

Summary of Contents

Page 1 - BEAM SETTER Model:

The SEALEY BODYSHOP/WORKSHOP HEADLAMP BEAM SETTER, HBS2001, is supplied with a fixed column, mirror and visor. ThisHEADLAMP BEAM SETTER may be used fo

Page 2 - 6. METHOD OF INSPECTION

6.1. Start engine, so that battery is not drained.6.2. Align the HBS with the centre of the headlamp to be tested, as in Section 5.6.4. With an assist

Page 3 - 7. THE LUXMETER

When testing symmetrical dipped beamsthe projection on the plate should be ahorizontal line.Correct projection on panel. SYMMETRICAL DIPPED BEAMIt is

Page 4 - 8. CALIBRATION

HBS2001 - 2 - 061103We suggest that the unit has periodic calibration checks in situ. If the unit is covered by a service agreement with the MOT packa

Page 5 - HBS2001 - 2 - 061

The Headlamp Beam Setter is equipped with a spirit level located on the base of the optical box, which is visible through the transparent panel.To lev

Page 6

Sole UK Distributor,Sealey Group,Bury St. Edmunds, Suffolk.PARTS LIST FOR:BODYSHOP/WORKSHOP HEADLAMPBEAM SETTER Model:HBS2001Date: 060405Issue: 301284

Comments to this Manuals

No comments

Sealey HBS2001 User Manual

Browse online or download User Manual for For the car Sealey HBS2001. Sealey HBS2001 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Sealey HBS2001