Sealey PW2200 User Manual Page 4

  • Download
  • Add to my manuals
  • Print
  • Page
    / 5
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 3
Original Language Version
Note: The pressure of the spray on the surface you are cleaning increases as you move the nozzle closer to the surface.
5.5.2. For the high pressure Turbo spray fit the turbo nozzle. This nozzle is intended for maximum cleaning affect.
5.6. Usingdetergent.Use only detergents approved for use in pressure washers.
PC2200: The PC2200 has the facility to use two different detergents (e.g: a traffic film remover and a general detergent).
5.6.1. Fill the detergent tanks with the required detergents (if required, only one tank can be used).
5.6.2. Turn the detergent selector control (fig.7) in the direction of the tank containing the required detergent.
PC2500:
5.6.3. Fill the detergent tank (fig.8) at the rear of the machine.
Both machines:
5.6.4. To switch to detergent mode, simply push the variable nozzle forwards to activate the low pressure setting. Pull the nozzle backwards
to resume normal washing.(fig.6)
5.6.5. Dirt is dissolved by applying detergent to the dry surface. On vertical surfaces, work from the bottom upwards.
5.6.6. Leave the detergent to act for 1-2 minutes, but DO NOT allow the surface to dry out.
5.6.7. To wash down select the variable spray jet nozzle set on the wide fan setting (fig.6).
5.6.8. When you have finished the soap application, remove the bottle and flush clean water through the tube until it is cleaned thoroughly.
Note: Failure to clean properly will cause the injection system to become clogged and inoperable.
5.7. When washing is completed.
5.7.1. Switch the power supply off by turning switch to 'Off' position (fiig.5).
5.7.2. Turn off the water supply tap.
5.7.3. Discharge residual pressure by pressing the trigger until no more water comes out of the nozzle.
WARNING! Failure to discharge pressure could result in personal injury.
5.7.4. Disconnect the inlet and high pressure outlet hoses.
5.7.5. Wipe the machine clean and dry and store in a clean, safe, dry, childproof location.
Note: a) DO NOT leave motor switched on for more than 15 minutes without operating trigger.
b) If the water pressure drops (e.g. someone else using the same water supply), the washer will not operate correctly.
Immediately switch the motor off and wait until the pressure is restored.
© Jack Sealey Ltd
6. TROUBLESHOOTINGGUIDE
SYMPTOMS REASON REMEDY
Motor will not start. 1. Loose or diconnected plug.
2. Blown fuse.
1. Reconnect plug.
2. See below
Circuit breaker trips or fuse blown. 1. Circuit Overload.
2. Extension cord too long or wire size too
small.
3. Nozzle partially blocked, causing
excessive pressure.
1. Check that the circuit is rated 13amps or
greater. Disconnect all loads on the circuit.
2. Use proper extension cord as
recommended in section 1.
3. Clean nozzle as described in maintenance
section.
Water or oil leaking from bottom of pump. 1. A small amount of leakage is normal. 1. If excessive leaking occurs contact
authorised service agent.
Trigger will not move. 1. Gun safety lock engaged. 1. Release safety lock.
Unit will not stop when trigger is released. 1. Trigger system not operating properly. 1. Contact authorised service agent.
Motor running but pump not building.
maximum pressure or has irregular pressure.
1. Water supply not turned on.
2. Unit has been stored in freezing
temperatures.
3. Water inlet screen clogged.
4. Kink in supply hose.
5. Nozzle worn out.
6. Air in pump.
7. Suction or discharge valves clogged or
worn out.
1. Turn on water supply.
2. Thaw out unit completely including hose,
gun and attachments.
3. Clean screen as described in maintenance
section.
4. Straighten hose.
5. Replace nozzle.
6. Let pressure washer run with gun open
and lance removed until a steady stream
of water is released.
7.Contact authorised service agent.
Original Language Version
PW2200,PW2500 Issue: 3 (I) - 14/10/13
Page view 3
1 2 3 4 5

Comments to this Manuals

No comments